Jump to content


Photo

Where Is The Alternate D0 On The Bottom?


  • Please log in to reply
6 replies to this topic

#1 Vedette

Vedette

    X-S Member

  • Members
  • Pip
  • 72 posts

Posted 25 September 2003 - 08:20 PM

Ok, I've checked a whole bunch of sites, and it seems that they all basically have the same pictures. When referring to the picture at the bottom of the page on http://www.xbox-scen...n_diagrams.html , it shows the d0 as part of a sort of string of other points. In the v1.3, theres not the same number of points....so i dont know which one it is.

Is it possible to solder to an alternate d0 in v1.3? i havent read anything that says that its specific to older versions of the xbox.

Edited by Vedette, 25 September 2003 - 08:20 PM.


#2 afortaleza

afortaleza

    X-S Member

  • Members
  • Pip
  • 131 posts
  • Location:Brazil
  • Xbox Version:v1.2
  • 360 version:v4.0 (jasper)

Posted 25 September 2003 - 10:39 PM

Are you *sure* that:

1) You have version 1.3
2) You are really looking for it in the right area

? I have a 1.2 board and I've soldered the alternative d0, it's really easier than the original d0. I have a x2 Pro and I did a pin-header install and passed the gray wire (d0 one) throught one of the available (nos soldered) LPC holes to reach the alternative d0 point, no cable extension using this smile.gif

regards
-- Anderson

#3 A@ron

A@ron

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,380 posts
  • Xbox Version:unk

Posted 26 September 2003 - 01:40 AM

Here... its what you need and its what I used for my install. Its a lot better resolution then the one in the tutorials section.

A@ron

#4 looop69

looop69

    X-S Senior Member

  • Members
  • PipPip
  • 167 posts
  • Location:Bluegrass State
  • Xbox Version:v1.3
  • 360 version:v1 (xenon)

Posted 26 September 2003 - 01:57 AM

I have a 1.3 that is soldered to alt d0.....I just used the pic at the bottom of the page you listed the first time I installed a chip

#5 Vedette

Vedette

    X-S Member

  • Members
  • Pip
  • 72 posts

Posted 26 September 2003 - 05:03 PM

I am SURE that i have a 1.3, serial numbers match, manufacturer's dates match, and i got a samsung dvd.

but looop69, the number of points in the string dont match that which is on the 1.3 board, how did you know which to solder to?

#6 Dissolved

Dissolved

    X-S Senior Member

  • Members
  • PipPip
  • 156 posts
  • Interests:xbox :D
  • Xbox Version:none
  • 360 version:v1 (xenon)

Posted 26 September 2003 - 05:19 PM

use a multi meter, the good ones have a Ground check with buzzer.



#7 afortaleza

afortaleza

    X-S Member

  • Members
  • Pip
  • 131 posts
  • Location:Brazil
  • Xbox Version:v1.2
  • 360 version:v4.0 (jasper)

Posted 26 September 2003 - 08:10 PM

QUOTE (Vedette @ Sep 26 2003, 07:03 PM)
I am SURE that i have a 1.3, serial numbers match, manufacturer's dates match, and i got a samsung dvd.

but looop69, the number of points in the string dont match that which is on the 1.3 board, how did you know which to solder to?

Can you send us any picture of your mobo ??




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users