Jump to content


Photo

X2.3 Lite + Problems


  • Please log in to reply
8 replies to this topic

#1 xbox11334

xbox11334

    X-S X-perience

  • XS-BANNED
  • PipPip
  • 410 posts
  • Xbox Version:unk

Posted 18 December 2003 - 10:04 PM

i just bought an x2.3 lite +, and i installed it, and got the usb power adaptersupplied so all the lights were on, or so until i turned the modchip on, the minute i turn the modchip on, the green light goes off, and the xbox frags...ppl said it was my lpc ports that they were dirty but i doubt it, cuz why would that make the green light go off....any suggestions at all???

#2 xbox11334

xbox11334

    X-S X-perience

  • XS-BANNED
  • PipPip
  • 410 posts
  • Xbox Version:unk

Posted 18 December 2003 - 10:10 PM

could it be the bios??? i know a bad bios makes it frag, but i didn't flash the bios yet, i got it from smt, and the greeen light on the chip goes off, would the green d0 light on the chip go off if it's a bad bios

#3 sparkac

sparkac

    X-S X-perience

  • Members
  • PipPip
  • 393 posts

Posted 18 December 2003 - 10:21 PM

frags are usually caused by the lpc ports, clean them

also check if your modchip is aligned

#4 lan122

lan122

    X-S Expert

  • Members
  • PipPipPip
  • 566 posts
  • Xbox Version:v1.4
  • 360 version:v1 (xenon)

Posted 18 December 2003 - 11:51 PM

Never used a 2.3 lite +, but on a 2.2 lite + the green light on the chip is supposed to go off when the chip is enabled.

As far a the frags, those suckers can be pretty hard to get llined up.

Also I have heard that it is important to make sure you have a good ground with those 2.3's. Check the tut on installing there's a section on grounding the chip.

#5 xbox11334

xbox11334

    X-S X-perience

  • XS-BANNED
  • PipPip
  • 410 posts
  • Xbox Version:unk

Posted 19 December 2003 - 07:34 PM

how do i clean the lpc ports, and i think it is aligned, cuz the green light shows that the d0 is, and i checked the lpcs, is there a way to clean the lpc ports without killing them like with a razor, cna i just cleant hem with my hands, cuz i already tried that

#6 xbox11334

xbox11334

    X-S X-perience

  • XS-BANNED
  • PipPip
  • 410 posts
  • Xbox Version:unk

Posted 19 December 2003 - 07:35 PM

could the frags be becuzof a bad bios it came with, i have a programmer?

and where can i find tuts on 2.3s, i've chexcked system-mods.com, and i've looked at all of theirs

Edited by xbox11334, 19 December 2003 - 07:35 PM.


#7 DexX

DexX

    X-S Senior Member

  • Members
  • PipPip
  • 167 posts

Posted 19 December 2003 - 07:49 PM

well how did you install your chip with what tutorials?

#8 BobDobbs

BobDobbs

    X-S Enthusiast

  • Members
  • 11 posts

Posted 19 December 2003 - 08:09 PM

Well, I've installed 3 X2.3+ chips this week... I had some problems with one of them... they sent me a bad USB board. Couldn't get BLUE lights on. (Had to splice and solder power straight to Controller port wires to avod waiting smile.gif )

If it reboots 3 times then FRAGs you need to get your D0 aligned. (green light may still come on, tho). I had to also use my dremel to elongate the screw hole (TOWARDS THE CHIP) to get one installed. I could plainly see that the D0 spiked pin was too far FORWARD. This completely fixed the problem! This was a version 1.1 . Also may sure of the obvious... is your switch set for the correct version?

BobDobbs

#9 xbox11334

xbox11334

    X-S X-perience

  • XS-BANNED
  • PipPip
  • 410 posts
  • Xbox Version:unk

Posted 19 December 2003 - 08:50 PM

i tested my version, and from what i tested i'm a version 1.0, but maybe they're wrong, if i switch the switch will i screw up my xbox if it's wrong?




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users