Jump to content


Photo

Install A Switch On The X-ecuter.


  • Please log in to reply
8 replies to this topic

#1 Raiders4ever

Raiders4ever

    X-S Young Member

  • Members
  • Pip
  • 47 posts

Posted 16 December 2002 - 02:39 AM

How would I wire this? I keep getting red/green flashes.

#2 MartialXboxArtist

MartialXboxArtist

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,455 posts
  • Xbox Version:v1.0
  • 360 version:unknown

Posted 16 December 2002 - 03:45 AM

Turn the 6 metal post towards you horizontally. Choose either 2 post all the way to the left or vice versa. Solder your wires on ONLY 2 metal posts that are close to each other vertically. Don't solder anything in the MIDDLE two posts. Not needed. I hope that helps! Good luck! smile.gif

Edited by MartialXboxArtist, 16 December 2002 - 03:48 AM.


#3 Raiders4ever

Raiders4ever

    X-S Young Member

  • Members
  • Pip
  • 47 posts

Posted 16 December 2002 - 03:48 AM

Thanks. I totally fucked that little solder point. I will just use the one on the back. i am really good at soldering to. I think I let my iron get to damn hot. Its a easy fix though.

#4 MartialXboxArtist

MartialXboxArtist

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,455 posts
  • Xbox Version:v1.0
  • 360 version:unknown

Posted 16 December 2002 - 03:50 AM

Don't use any iron higher than 15 watts on delicate circuit board like the Xbox. I used only a 15 watt myself and it gets dang hot for just 15 watts! I feel bad for the newbie that uses a 100 watt or something. ohmy.gif

#5 Satan00

Satan00

    PimpMaster

  • Members
  • PipPipPipPipPip
  • 1,113 posts
  • Location:New York
  • Xbox Version:v1.0
  • 360 version:v1 (xenon)

Posted 16 December 2002 - 03:56 AM

i have a switch running off the back points
its easy
take the d0 and wire it to one of the pins of the switch
take the ground and wire it to the other pin of the switch

#6 MartialXboxArtist

MartialXboxArtist

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,455 posts
  • Xbox Version:v1.0
  • 360 version:unknown

Posted 16 December 2002 - 04:03 AM

I also have a switch. It's mounted on the inside connected to the metal shielding. It's out of sight and works perfect as of now. smile.gif

#7 Captain_Dunsel

Captain_Dunsel

    X-S Member

  • Members
  • Pip
  • 96 posts

Posted 16 December 2002 - 05:39 AM

Folks, I presume we're discussing wiring an enable/disable for the original X-ecuter chip...?

If so, can you point me to a wiring diagram for the chip, and please triple-verify the connections that you are making/breaking to enable/disable the chip?

I'd like to add this info to my Adding Switches tutorial -- I don't currently have info for the X-ecuter.

Thanks,


Captain Dunsel

#8 MURDERER

MURDERER

    X-S Senior Member

  • Members
  • PipPip
  • 285 posts

Posted 16 December 2002 - 07:58 AM

Yea, check out my website for how to install the switch.

iMURDERER

#9 Raiders4ever

Raiders4ever

    X-S Young Member

  • Members
  • Pip
  • 47 posts

Posted 16 December 2002 - 10:03 PM

Thanks guys. I got it working seems like I just had it wired wrong.




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users