Jump to content


Photo

Flashing Help - Puh-leeeeeese


  • Please log in to reply
9 replies to this topic

#1 legofool

legofool

    X-S Enthusiast

  • Members
  • 4 posts

Posted 16 March 2004 - 04:13 PM

Hey, y'all.

So i got my mod yesterday, sat down, installed the thing and then found [i think] all the *cough software cough* needed to finish the deal.

HOWEVER

I get to the Cromwell screen, the whole "Flash in progress" bit and it does its little spiel. The bar goes yellow, the bar goes green, the bar goes away and the xbox turns off.

But then when i go to start the machine up again, it wants to Flash it again. I've done this twenty times.

Also, when i turn the machine on from "Bank 1" I get the normal xbox loading thing. I've read [i think] just about every readme out there and honestly can't find the answers. I've been at this since 4pm yesterday.

I really don't know what I'm doing wrong. Please, any help would be greatly appreciated...

-the fool.
javascript:emoticon(':jester:')

#2 xaser

xaser

    X-S Member

  • Members
  • Pip
  • 145 posts

Posted 16 March 2004 - 04:16 PM

is flah protection on?

#3 Xtrem

Xtrem

    The Next Level

  • Members
  • PipPipPipPipPipPipPipPip
  • 4,670 posts
  • Location:My Place In Montreal
  • Xbox Version:unk
  • 360 version:v1 (xenon)

Posted 16 March 2004 - 04:18 PM

Ok If Your Mod Is On And You Get The Normal Ms™ Dash That Means That You Are To Put The EvoX Boot Disc In There.

#4 legofool

legofool

    X-S Enthusiast

  • Members
  • 4 posts

Posted 16 March 2004 - 04:18 PM

naw - it's set to "unprotect"

#5 duudfromnorway

duudfromnorway

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,631 posts
  • Xbox Version:unk
  • 360 version:unknown

Posted 16 March 2004 - 04:22 PM

what size did you flash it with?

#6 Xtrem

Xtrem

    The Next Level

  • Members
  • PipPipPipPipPipPipPipPip
  • 4,670 posts
  • Location:My Place In Montreal
  • Xbox Version:unk
  • 360 version:v1 (xenon)

Posted 16 March 2004 - 04:22 PM

QUOTE (legofool @ Mar 16 2004, 01:18 PM)
naw - it's set to "unprotect"

Like I Said When You Are Finish Nothing As Change Just That Now It Can Read Other Things Like EvoX

#7 legofool

legofool

    X-S Enthusiast

  • Members
  • 4 posts

Posted 16 March 2004 - 04:26 PM

i flashed it with a 512k, as i'd read in the tuts. but i can only flash Bank 2 [or am i only SUPPOSED to flash bank 2 and then flip it over to bank 1?]

y'see, i'm not sure if the thing has been flashed "properly" because it keeps wanting to be flashed everytime i start the thing up from "bank 2"

i really appreciate all of you helping out here, i hope i don't come across as a TOTAL idiot...

-the fool.

#8 xaser

xaser

    X-S Member

  • Members
  • Pip
  • 145 posts

Posted 16 March 2004 - 04:29 PM

so after you flash it.. it reboots and then it wants you to flash again? or do you c the MS screen?

#9 duudfromnorway

duudfromnorway

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,631 posts
  • Xbox Version:unk
  • 360 version:unknown

Posted 16 March 2004 - 04:29 PM

nope, jump to bank one and stuff the evox boot disk in.
if bank is set to 2 when flashing, you`re flashing bank 1, and when booting from bank one you end up in msdash, ready to load any disk( install evox if you like).
note! this is with a 512 bios.....

Edited by duudfromnorway, 16 March 2004 - 04:31 PM.


#10 legofool

legofool

    X-S Enthusiast

  • Members
  • 4 posts

Posted 16 March 2004 - 04:33 PM


If i leave it on Bank 2 and rebbot, it wants to flash again.

If i set the switch to Bank 1 and reboot, i get the MS loadup screen

-the fool.

ps - all of you fine people rock.




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users