Jump to content


Photo

Xecuter 2.3 Lite + Installed But


  • Please log in to reply
9 replies to this topic

#1 atriedes38

atriedes38

    X-S Member

  • Members
  • Pip
  • 91 posts

Posted 19 May 2004 - 08:42 PM

I have all jumpers set correctly. I'm following instructions to the letter. I get all three leds when disabled. When i enable and power up the Xbox powers up and off, up and off, then powers on steady on third try but FRAGs.
What am i doing wrong?

#2 chefelf

chefelf

    Brandishing the Triforce of Modding

  • Head Moderators
  • PipPipPipPipPipPipPipPipPipPipPip
  • 7,407 posts
  • Gender:Male
  • Location:New York, NY
  • Interests:Video Games, Web Design, Writing, Cycling, Hardware Modification, Building Computers, Music
  • Xbox Version:v1.3
  • 360 version:unknown

Posted 19 May 2004 - 08:50 PM

Sounds like your chip isn't properly aligned.

#3 atriedes38

atriedes38

    X-S Member

  • Members
  • Pip
  • 91 posts

Posted 19 May 2004 - 09:06 PM

So is the power stutter normal if the chip is mis-alligned? I can onle seem to get all three light in one certain position and that Frags. How much can I wiggle the chip around without frying my Xbox?

#4 twisted.penguin

twisted.penguin

    X-S Freak

  • XS-BANNED
  • PipPipPipPipPip
  • 1,465 posts
  • Xbox Version:v1.3

Posted 19 May 2004 - 09:10 PM

You also may want to tighten/loosen the screw (be carefull not to strip or your jacked, you'll need a new base.) , same thing happened to a friend. Yes, that fragging is normal, check the manual at the Xecuter website. wink.gif

#5 atriedes38

atriedes38

    X-S Member

  • Members
  • Pip
  • 91 posts

Posted 19 May 2004 - 09:18 PM

Thanks. That was the tutorial I was using. I know the FRAG is normal but is the power stutter? Is there a chance I have a bad chip?

#6 chefelf

chefelf

    Brandishing the Triforce of Modding

  • Head Moderators
  • PipPipPipPipPipPipPipPipPipPipPip
  • 7,407 posts
  • Gender:Male
  • Location:New York, NY
  • Interests:Video Games, Web Design, Writing, Cycling, Hardware Modification, Building Computers, Music
  • Xbox Version:v1.3
  • 360 version:unknown

Posted 19 May 2004 - 09:19 PM

QUOTE (atriedes38 @ May 19 2004, 06:18 PM)
Thanks. That was the tutorial I was using. I know the FRAG is normal but is the power stutter? Is there a chance I have a bad chip?

The power up, power off thing is all part of fragging. It's normal if the chip is not aligned or the BIOS is not found some other way. smile.gif

#7 atriedes38

atriedes38

    X-S Member

  • Members
  • Pip
  • 91 posts

Posted 19 May 2004 - 09:26 PM

Got it. Hooray!!

Thanks guys. This forum rocks.

Expect me to come crying any minute when I try to flash this mother.

#8 Slimer_85

Slimer_85

    X-S Member

  • Members
  • Pip
  • 61 posts

Posted 19 May 2004 - 09:54 PM

I have the exact same problem, but i did strip out the little screw thingy. Where can i go to get a new little under board thing???

#9 Tfizzle

Tfizzle

    X-S X-perience

  • Members
  • PipPip
  • 371 posts

Posted 19 May 2004 - 09:57 PM

there is a bolt method. supposedly its more secure than the screw method. go search the tuts.

#10 Slimer_85

Slimer_85

    X-S Member

  • Members
  • Pip
  • 61 posts

Posted 19 May 2004 - 10:00 PM

Thanks man




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users