Jump to content


Photo

Cuttin A Hole


  • Please log in to reply
12 replies to this topic

#1 dougMod

dougMod

    X-S Messiah

  • Members
  • PipPipPipPipPipPipPip
  • 3,031 posts
  • Location:HH,Ca (USA)
  • Xbox Version:unk
  • 360 version:unknown

Posted 09 June 2004 - 12:36 AM

Well i made a switch for my LED jewel mod and want 2 put it in the back panel. I cant seem 2 get it off . Do i take the MOBO out and everythin?

#2 krappy

krappy

    X-S X-perience

  • XS-BANNED
  • PipPip
  • 415 posts
  • Location:Reppin Da @-Town
  • Xbox Version:v1.4

Posted 09 June 2004 - 12:39 AM

i think u should man so you wont mess anything up

#3 dougMod

dougMod

    X-S Messiah

  • Members
  • PipPipPipPipPipPipPip
  • 3,031 posts
  • Location:HH,Ca (USA)
  • Xbox Version:unk
  • 360 version:unknown

Posted 09 June 2004 - 12:40 AM

no,i need 2 get the back panel off

#4 BobBrkersMyHero

BobBrkersMyHero

    X-S Enthusiast

  • XS-BANNED
  • 0 posts
  • Location:Erie, PA
  • Xbox Version:v1.0
  • 360 version:v1 (xenon)

Posted 09 June 2004 - 12:44 AM

there is no..back panel....

#5 kramit

kramit

    X-S Senior Member

  • Members
  • PipPip
  • 175 posts

Posted 09 June 2004 - 12:47 AM

I think hes referring to the metal shielding?

#6 dougMod

dougMod

    X-S Messiah

  • Members
  • PipPipPipPipPipPipPip
  • 3,031 posts
  • Location:HH,Ca (USA)
  • Xbox Version:unk
  • 360 version:unknown

Posted 09 June 2004 - 12:48 AM

no, the place where the LAN ports is video hook up is. LOL cause i can mod with the lights just i found out how 2 use a dremel yesterday and have been practiciing so now i cna finiall sup a hole with out the hole saw. LOL

#7 IITangoCrazy

IITangoCrazy

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,106 posts
  • Location:Ontario, Canada
  • Xbox Version:v1.0

Posted 09 June 2004 - 12:52 AM

man that is part of the bottom of the case . . . the case is 3 parts the front pannel the top piece that has the sides on it and the base which also has the back attached.

#8 dougMod

dougMod

    X-S Messiah

  • Members
  • PipPipPipPipPipPipPip
  • 3,031 posts
  • Location:HH,Ca (USA)
  • Xbox Version:unk
  • 360 version:unknown

Posted 09 June 2004 - 12:54 AM

ya , so i just remnove the MOBO rite and it will come off

#9 Comcipher

Comcipher

    X-S Expert

  • Members
  • PipPipPip
  • 521 posts
  • Location:Illinois, USA
  • Xbox Version:v1.0

Posted 09 June 2004 - 12:56 AM

Yeah, i'd suggest taking the mobo out and everything... depends if you want to drill straight through both the metal and the plastic back or do them seperatly as to whether you'll have to take it apart even further.

#10 xboxhackcrack

xboxhackcrack

    X-S Senior Member

  • Members
  • PipPip
  • 264 posts
  • Xbox Version:unk

Posted 09 June 2004 - 12:56 AM

the back where the lan port and stuff is does not come off. It is molded into the bottom of the case

#11 dougMod

dougMod

    X-S Messiah

  • Members
  • PipPipPipPipPipPipPip
  • 3,031 posts
  • Location:HH,Ca (USA)
  • Xbox Version:unk
  • 360 version:unknown

Posted 09 June 2004 - 01:00 AM

ok, yes i want 2 cut on the bottom part of the case. WHErE the LAN hook up is to make a room for my switch

#12 HHN-Zero1

HHN-Zero1

    X-S Member

  • Members
  • Pip
  • 108 posts
  • Xbox Version:unk

Posted 09 June 2004 - 01:01 AM

When I added a push button switch I just drill a hole in the back, throught the plastic and metal case, close to the lan port and just alittle bit higher, made sure there wasn't anything behind where I was going to drill. I didn't take out anything, I didn't want to wait, so I flipped the case upside down and drilled and I made sure to clean off the mobo with some compressed air when I was done.

#13 dougMod

dougMod

    X-S Messiah

  • Members
  • PipPipPipPipPipPipPip
  • 3,031 posts
  • Location:HH,Ca (USA)
  • Xbox Version:unk
  • 360 version:unknown

Posted 09 June 2004 - 01:02 AM

k thx ill do it now




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users