Jump to content


Photo

Need Help Asap With Install (getting Errors)


  • Please log in to reply
5 replies to this topic

#1 ddzc

ddzc

    X-S X-perience

  • Members
  • PipPip
  • 371 posts
  • Xbox Version:v1.6

Posted 12 September 2004 - 12:51 AM

I checked everything over and everything looks perfecty fine. Anyone know what this error can be and what I should specifically check on the install.

When I boot the machine, it goes on then off, then on again then off (stays on for not even a second) then on the 3rd try it boots and nothing shows on the screen and the eject button flashes green and red.

Installing a duox2 set to bank 1 (my machine is a v 1.6)

Thanks

Edited by ddzc, 12 September 2004 - 12:52 AM.


#2 Nightfire-Player

Nightfire-Player

    X-S Hacker

  • Members
  • PipPipPipPipPipPip
  • 2,403 posts
  • Location:Jersey Channel Islands - UK
  • Xbox Version:v1.4
  • 360 version:none

Posted 12 September 2004 - 12:54 AM

Yea its fragging, it usually means that the chip isnt placed properly. Check all the points on it and make sure everything is touching right.

Also if you had just tried to flash the chip then it indicate a bad flash.

#3 ddzc

ddzc

    X-S X-perience

  • Members
  • PipPip
  • 371 posts
  • Xbox Version:v1.6

Posted 12 September 2004 - 01:04 AM

Thanks a lot nightfire. I'll check every point right now and update to see how it goes. BTW I never flashed it, it was the first bootup.

#4 ddzc

ddzc

    X-S X-perience

  • Members
  • PipPip
  • 371 posts
  • Xbox Version:v1.6

Posted 12 September 2004 - 01:26 AM

Ok I applied more solder to some pins on the chip b/c it looked like some had a bit too less so maybe the contact wasn't strong enough.

Other than that, everything looks fine. I just put it back together and the exact same thing.

I followed this diagram

http://www.duomodchi.../duox2_v1.6.jpg

Used the pin headers how it's shown in the last pic, soldered everything on the bottom of the board and all the wires are perfectly soldered, no bridges no mess.

This is the only thing I can think of. I cut those two legs so I can slide the chip into the pin header on the top. Do I have to cut the ones on the bottom off too.
Other than the two I clipped, every other leg top and bottom is soldered. This is where something may be wrong, maybe some aren't supposed to be soldered. Anyone got any ideas there?

Any help would be great, thanks everyone

#5 ddzc

ddzc

    X-S X-perience

  • Members
  • PipPip
  • 371 posts
  • Xbox Version:v1.6

Posted 12 September 2004 - 01:59 AM

Here's a couple of pics if anyone is interested to viewing them. Thanks

Top Pic

Bottom Pic



#6 ddzc

ddzc

    X-S X-perience

  • Members
  • PipPip
  • 371 posts
  • Xbox Version:v1.6

Posted 12 September 2004 - 04:27 AM

someone must have any ideas... im stumped sad.gif

I looked at this pic here

http://www.duomodchi...duox/header.jpg

See that one hole unfilled, if that's filled, can it screw everything up even though there's no wire attatched on the bottom of the pin header?

Edited by ddzc, 12 September 2004 - 04:51 AM.





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users