Jump to content


Photo

Lpc Pcb Rebuild


  • Please log in to reply
10 replies to this topic

#1 patchesreusch

patchesreusch

    X-S Senior Member

  • Members
  • PipPip
  • 193 posts
  • Location:2310 arnold st. Savanna, Illinois
  • Interests:jhaqj-ds00w-bgepg-v9djr9-kk3480
  • Xbox Version:v1.4
  • 360 version:v1 (xenon)

Posted 04 May 2007 - 02:07 AM

i have the board and want to know if i just apply a lot of solder or i get some sort of wire?

#2 patchesreusch

patchesreusch

    X-S Senior Member

  • Members
  • PipPip
  • 193 posts
  • Location:2310 arnold st. Savanna, Illinois
  • Interests:jhaqj-ds00w-bgepg-v9djr9-kk3480
  • Xbox Version:v1.4
  • 360 version:v1 (xenon)

Posted 04 May 2007 - 12:11 PM

does anyone know how to install the pcb or what?

#3 commandersafi

commandersafi

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,581 posts
  • Location:Houston, Texas
  • Xbox Version:none
  • 360 version:none

Posted 04 May 2007 - 12:26 PM

You just set the rebuild board over the LPC port, and apply a little bit of solder to connect the soldering pads on the rebuild board to the motherboard

Its best if you Put some flux to the places your going to be soldering wink.gif

#4 patchesreusch

patchesreusch

    X-S Senior Member

  • Members
  • PipPip
  • 193 posts
  • Location:2310 arnold st. Savanna, Illinois
  • Interests:jhaqj-ds00w-bgepg-v9djr9-kk3480
  • Xbox Version:v1.4
  • 360 version:v1 (xenon)

Posted 04 May 2007 - 08:59 PM

do i solder the pin header first?

#5 xboxgamer733

xboxgamer733

    X-S Moderating Team

  • Head Moderators
  • PipPipPipPipPipPipPip
  • 3,803 posts
  • Gender:Male
  • Location:Moscow, Idaho
  • Xbox Version:v1.0
  • 360 version:v1 (xenon)

Posted 04 May 2007 - 09:38 PM

If you solder the LPC rebuild board to your Xbox's motherboard after the pin header is installed, it won't be able to lay flat against the motherboard.

Because of this, I recommend applying solder to the pin header pins after you have installed the rebuild board.

Edited by xboxgamer733, 04 May 2007 - 09:38 PM.


#6 patchesreusch

patchesreusch

    X-S Senior Member

  • Members
  • PipPip
  • 193 posts
  • Location:2310 arnold st. Savanna, Illinois
  • Interests:jhaqj-ds00w-bgepg-v9djr9-kk3480
  • Xbox Version:v1.4
  • 360 version:v1 (xenon)

Posted 04 May 2007 - 09:41 PM

how do i put on the solder to the pins after the board is installed?

#7 blame canada

blame canada

    X-S Hacker

  • XS-BANNED
  • PipPipPipPipPipPip
  • 2,356 posts
  • Location:Good ol' Chicago
  • Xbox Version:v1.0
  • 360 version:v1 (xenon)

Posted 05 May 2007 - 12:44 AM

If done correctly, it should flow onto the pins and into the LPC holes. Couldn't tell ya exatly because I never use em (wire installs are easier IMO as you can see what is and isn't soldered 100% correctly. The board covers up the whole LPC holes so you don't know which one(s) are soldered correctly)

#8 patchesreusch

patchesreusch

    X-S Senior Member

  • Members
  • PipPip
  • 193 posts
  • Location:2310 arnold st. Savanna, Illinois
  • Interests:jhaqj-ds00w-bgepg-v9djr9-kk3480
  • Xbox Version:v1.4
  • 360 version:v1 (xenon)

Posted 05 May 2007 - 03:08 AM

ya i tried the lpc thing like i shouldn't have and broke a trace and got a pin header stuck in there

#9 blame canada

blame canada

    X-S Hacker

  • XS-BANNED
  • PipPipPipPipPipPip
  • 2,356 posts
  • Location:Good ol' Chicago
  • Xbox Version:v1.0
  • 360 version:v1 (xenon)

Posted 05 May 2007 - 01:21 PM

thus, why I suggested using wires as you now have to desolder the entire lpc board, fix the trace, and re-do the rebuild either (at your own risk lol) with the lpc rebuild board or with wires.

#10 alanmanquero

alanmanquero

    X-S Enthusiast

  • XS-BANNED
  • 20 posts
  • Location:tumami!
  • Interests:XBOX DUHHH!
  • Xbox Version:v1.6
  • 360 version:v1 (xenon)

Posted 11 May 2007 - 09:02 PM

hei i got a 1.6 with the rebuild and its not a big deal...just solder the pins first without adding to much solder to it...then the lpc rebuild...sometimes u dont need more solder it will jsut stick together without problem...also flux its a good idea like that dude said!...just as a tip be carefull on not leaving more than 3 seconds the iron in the motherboard because it could be damaged =]

#11 Chancer

Chancer

    Don't You Trust me?

  • Head Moderators
  • PipPipPipPipPipPipPipPipPipPipPipPipPipPipPip
  • 18,687 posts
  • Gender:Male
  • Xbox Version:v1.6
  • 360 version:v3.0 (falcon)

Posted 11 May 2007 - 09:47 PM

QUOTE(alanmanquero @ May 11 2007, 09:38 PM) View Post

hei i got a 1.6 with the rebuild and its not a big deal...just solder the pins first without adding to much solder to it...then the lpc rebuild...sometimes u dont need more solder it will jsut stick together without problem...also flux its a good idea like that dude said!...just as a tip be carefull on not leaving more than 3 seconds the iron in the motherboard because it could be damaged =]

Too Late

QUOTE
ya i tried the lpc thing like i shouldn't have and broke a trace and got a pin header stuck in there






0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users