Jump to content


Photo

Hddhackr Error No Drive Found


  • Please log in to reply
18 replies to this topic

#1 peter5898

peter5898

    X-S Enthusiast

  • Members
  • 1 posts

Posted 12 June 2007 - 10:50 PM

I have just tried to modify my new western digital hard drive with the hddhackr program – when I boot into dos and I try to run the program I receive the error:-

No Drive found in Enhanced mode, now scanning in legacy mode

Type the nr of the drive you want to use (1 to 4, x=exit)


I believe that my sata controller is ICH8R and my PC model is HP DC7600 I have included details of my hardware from msinfo32:-

I’m not sure if anyone can help me with this as I have tried to search the internet and forums for help but I haven’t got very far.

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&3E55312&0&1
I/O Port 0x00000170-0x00000177
I/O Port 0x00000376-0x00000376
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 23/12/2005 17:43)

Name Standard Dual Channel PCI IDE Controller
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCI\VEN_8086&DEV_27C0&SUBSYS_3011103C&REV_01\3&B1BFB68&0&FA
I/O Port 0x000010D8-0x000010DF
I/O Port 0x000010F0-0x000010F3
I/O Port 0x000010E0-0x000010E7
I/O Port 0x000010F4-0x000010F7
I/O Port 0x000010B0-0x000010BF
IRQ Channel IRQ 19
Driver c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 23/12/2005 17:45)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&1D1B703B&0&0
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 23/12/2005 17:43)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&1D1B703B&0&1
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), 93.13 KB (95,360 bytes), 23/12/2005 17:43)

ohmy.gif

#2 TheSpecialist

TheSpecialist

    X-S Senior Member

  • Members
  • PipPip
  • 289 posts

Posted 13 June 2007 - 05:34 PM

QUOTE(peter5898 @ Jun 13 2007, 12:26 AM) View Post

I believe that my sata controller is ICH8R


That's an intel. It should work in legacy mode, just like the hddhacker proposes. It should list your WD drive. If not, try changing your SATA controller in bios to 'legacy mode' instead of 'enhanced mode' (it seems you might have set it to 'enhanced mode' currently in your bios).

BTW, be careful in legacy mode, that you're selecting the right device and not some IDE device (especially take care if you have another WD drive in your system, don't flash the wrong HDD !) If in doubt, disconnect ALL other SATA and IDE devices.

Edited by TheSpecialist, 13 June 2007 - 05:40 PM.


#3 dylan_snyder09

dylan_snyder09

    X-S Member

  • Members
  • Pip
  • 75 posts
  • Xbox Version:v1.6
  • 360 version:v3.0 (falcon)

Posted 04 August 2008 - 05:16 AM

woops wrong thread that i thought i was responding to. sorry for necroposting on accident:s

Edited by dylan_snyder09, 04 August 2008 - 05:17 AM.


#4 guyver0

guyver0

    X-S Enthusiast

  • Members
  • 14 posts

Posted 06 November 2008 - 08:47 PM

i reall need help with this, i just bough a new bevs and im getting the same nr error, it says looking for the drive in enhanced mode which fails after which it looks for it in legacy mode and then asks me for the nr, why is this sad.gif
ive taken out my info from msinfo32 its the following:




Name Intel® 82801G (ICH7 Family) Ultra ATA Storage Controllers - 27DF
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_27DF&SUBSYS_4E538086&REV_01\3&61AAA01&0&F9
I/O Port 0x000030B0-0x000030BF
Driver c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 7:00 PM)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&1B8AFF68&0&0
I/O Port 0x000001F0-0x000001F7
I/O Port 0x000003F6-0x000003F6
IRQ Channel IRQ 14
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&1B8AFF68&0&1
I/O Port 0x00000170-0x00000177
I/O Port 0x00000376-0x00000376
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)

Name Intel® 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_27C0&SUBSYS_4E538086&REV_01\3&61AAA01&0&FA
I/O Port 0x000030C8-0x000030CF
I/O Port 0x000030E4-0x000030E7
I/O Port 0x000030C0-0x000030C7
I/O Port 0x000030E0-0x000030E3
I/O Port 0x000030A0-0x000030AF
IRQ Channel IRQ 19
Driver c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 7:00 PM)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&254E23F&0&0
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&254E23F&0&1
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)


#5 dmac271

dmac271

    X-S Enthusiast

  • Members
  • 19 posts

Posted 06 November 2008 - 09:24 PM

QUOTE(guyver0 @ Nov 6 2008, 01:23 PM) View Post

i reall need help with this, i just bough a new bevs and im getting the same nr error, it says looking for the drive in enhanced mode which fails after which it looks for it in legacy mode and then asks me for the nr, why is this sad.gif
ive taken out my info from msinfo32 its the following:


Name Intel® 82801G (ICH7 Family) Ultra ATA Storage Controllers - 27DF
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_27DF&SUBSYS_4E538086&REV_01\3&61AAA01&0&F9
I/O Port 0x000030B0-0x000030BF
Driver c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 7:00 PM)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&1B8AFF68&0&0
I/O Port 0x000001F0-0x000001F7
I/O Port 0x000003F6-0x000003F6
IRQ Channel IRQ 14
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&1B8AFF68&0&1
I/O Port 0x00000170-0x00000177
I/O Port 0x00000376-0x00000376
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)

Name Intel® 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_27C0&SUBSYS_4E538086&REV_01\3&61AAA01&0&FA
I/O Port 0x000030C8-0x000030CF
I/O Port 0x000030E4-0x000030E7
I/O Port 0x000030C0-0x000030C7
I/O Port 0x000030E0-0x000030E3
I/O Port 0x000030A0-0x000030AF
IRQ Channel IRQ 19
Driver c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 7:00 PM)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&254E23F&0&0
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&254E23F&0&1
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)




open hddhackr in hex editor and scroll all the way to the bottom.

youll see the numbers 4D 50 52 54 as being the last numbers

replace those numbers with 30 C8 30 C0 and then save the program and restart your computer and re run it.

it should then detect your SATA and work

#6 eskimomo

eskimomo

    X-S Enthusiast

  • Members
  • 5 posts

Posted 13 November 2008 - 10:53 PM

I'm having the same problem as the other two guys. I can't provide the information that they did because I'm running ubuntu, and as somewhat of a noob I don't know a program that would grab this kind of info.

Help is appreciated.

Eli

#7 bburpee

bburpee

    X-S Enthusiast

  • Members
  • 9 posts

Posted 15 November 2008 - 02:33 AM

I've tried a HP tx2000 laptop and a Sony Vaio laptop with a BEVS-VAT, no luck. Same problem as these other folks.

Both computers I get the "No drive found" (or similar) error, and neither laptop has many options to play with in the BIOS Setup, such as Legacy mode.

I've tried every SATA port on these machines, and hex edited the values found in these threads... ending in 60, 70, C0, and another value I can't recall.

The Vaio is a PCG-8Z2L, with an Intel 82801HEM/HBM SATA AHCI Controller (According to Device Manager).

Please, any suggestions are welcomed. (Sorry for posting similar versions of this in multiple threads - it's difficult to tell which will engender current responses)

#8 IllKidWags

IllKidWags

    X-S Enthusiast

  • Members
  • 2 posts

Posted 23 November 2008 - 10:50 PM

so i attempted to rewrite the last numbers in Hex workshop as Dmac suggested but with my own msinfo and Hddhackr acknowleged that the ports had been changed but it still came up with the same error.

Name Intel® ICH8R/ICH9R SATA RAID Controller
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_2822&SUBSYS_2A69103C&REV_02\3&11583659&0&FA
I/O Port 0x0000D880-0x0000D887
I/O Port 0x0000D800-0x0000D803
I/O Port 0x0000D480-0x0000D487
I/O Port 0x0000D400-0x0000D403
I/O Port 0x0000D080-0x0000D09F
Memory Address 0xF9CFF000-0xF9CFF7FF
IRQ Channel IRQ 19
Driver c:\windows\system32\drivers\iastor.sys (7.6.0.1011, 373.02 KB (381,976 bytes), 8/4/2008 10:17 PM)


what exactly would i do with this Sata port info?


#9 wangshu20

wangshu20

    X-S Enthusiast

  • Members
  • 3 posts

Posted 03 December 2008 - 02:37 PM

[quote name='IllKidWags' date='Nov 24 2008, 09:26 AM' post='4381886']
so i attempted to rewrite the last numbers in Hex workshop as Dmac suggested but with my own msinfo and Hddhackr acknowleged that the ports had been changed but it still came up with the same error.

[b]Name Intel® ICH8R/ICH9R SATA RAID Controller
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_2822&SUBSYS_2A69103C&REV_02\3&11583659&0&FA
I/O Port 0x0000D880-0x0000D887
I/O Port 0x0000D800-0x0000D803
I/O Port 0x0000D480-0x0000D487
I/O Port 0x0000D400-0x0000D403
I/O Port 0x0000D080-0x0000D09F
Memory Address 0xF9CFF000-0xF9CFF7FF
IRQ Channel IRQ 19
Driver c:\windows\system32\drivers\iastor.sys (7.6.0.1011, 373.02 KB (381,976 bytes), 8/4/2008 10:17 PM)


what exactly would i do with this Sata port info?[/b


I was having problems with this as well but i managed to get it to work. I was using
Name Intel® ICH8R/DO/DH SATA RAID Controller

I also edited hddhackr to look for my specific port numbers (in your case you would've replaced the 4D 50 52 54 with D8 80 D4 80?) and copied the edited version of hddhackr to my bootable flash drive.
I also ripped out all the power and data feeds to all my sata drives excepts the BEVS, which i plugged into sata port 1.
I also went into my BIOS settings and changed sata operation from "raid on" to "raid autodetect/ata". That's in a dell bios though.
I thought it wasn't going to make a difference but as soon as i powered up ran the command for hddhackr it detected it straight away.
Anyway give that a whirl, probably not any help but i thought i'd post anyway, because i know how frustrating it is. dry.gif





#10 wangshu20

wangshu20

    X-S Enthusiast

  • Members
  • 3 posts

Posted 03 December 2008 - 02:51 PM

QUOTE(guyver0 @ Nov 6 2008, 01:23 PM)

i reall need help with this, i just bough a new bevs and im getting the same nr error, it says looking for the drive in enhanced mode which fails after which it looks for it in legacy mode and then asks me for the nr, why is this
ive taken out my info from msinfo32 its the following:


Name Intel® 82801G (ICH7 Family) Ultra ATA Storage Controllers - 27DF
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_27DF&SUBSYS_4E538086&REV_01\3&61AAA01&0&F9
I/O Port 0x000030B0-0x000030BF
Driver c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 7:00 PM)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&1B8AFF68&0&0
I/O Port 0x000001F0-0x000001F7
I/O Port 0x000003F6-0x000003F6
IRQ Channel IRQ 14
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&1B8AFF68&0&1
I/O Port 0x00000170-0x00000177
I/O Port 0x00000376-0x00000376
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)

Name Intel® 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller - 27C0
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_27C0&SUBSYS_4E538086&REV_01\3&61AAA01&0&FA
I/O Port 0x000030C8-0x000030CF
I/O Port 0x000030E4-0x000030E7
I/O Port 0x000030C0-0x000030C7
I/O Port 0x000030E0-0x000030E3
I/O Port 0x000030A0-0x000030AF
IRQ Channel IRQ 19
Driver c:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 8/23/2001 7:00 PM)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&254E23F&0&0
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&254E23F&0&1
Driver c:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 8/4/2004 3:59 AM)





open hddhackr in hex editor and scroll all the way to the bottom.

youll see the numbers 4D 50 52 54 as being the last numbers

replace those numbers with 30 C8 30 C0 and then save the program and restart your computer and re run it.

it should then detect your SATA and work



From what i understand (based on his port numbers with 7) wouldn't he have to plug in 30 E4 30 C0?

#11 madnlooney

madnlooney

    X-S Enthusiast

  • Members
  • 22 posts
  • Location:south London, UK
  • Xbox Version:v1.0
  • 360 version:v1 (xenon)

Posted 18 December 2008 - 01:35 PM

is it possible to get some help too? i would like to know how to work out the hex editing then i can do mine and help others. here is my information and hddhackr doesnt detect my WD1200bevs



Name Standard Dual Channel PCI IDE Controller
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCI\VEN_10DE&DEV_0265&SUBSYS_81BC1043&REV_A1\3&2411E6FE&0&68
I/O Port 0x0000FD00-0x0000FD0F
Driver f:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 03/08/2004 13:00)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&F2CF138&0&0
I/O Port 0x000001F0-0x000001F7
I/O Port 0x000003F6-0x000003F6
Driver f:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 03/08/2004 13:00)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&F2CF138&0&1
I/O Port 0x00000170-0x00000177
I/O Port 0x00000376-0x00000376
Driver f:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 03/08/2004 13:00)

Name NVIDIA nForce 430/410 Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_0266&SUBSYS_81BC1043&REV_A1\3&2411E6FE&0&70
I/O Port 0x000009F0-0x000009F7
I/O Port 0x00000BF0-0x00000BF3
I/O Port 0x00000970-0x00000977
I/O Port 0x00000B70-0x00000B73
I/O Port 0x0000F800-0x0000F80F
Memory Address 0xFE02D000-0xFE02DFFF
IRQ Channel IRQ 23
Driver f:\windows\system32\drivers\nvata.sys (5.10.2600.0666 built by: WinDDK, 98.38 KB (100,736 bytes), 22/09/2008 20:31)

Name NVIDIA nForce 430/410 Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_0267&SUBSYS_81BC1043&REV_A1\3&2411E6FE&0&78
I/O Port 0x000009E0-0x000009E7
I/O Port 0x00000BE0-0x00000BE3
I/O Port 0x00000960-0x00000967
I/O Port 0x00000B60-0x00000B63
I/O Port 0x0000F300-0x0000F30F
Memory Address 0xFE02C000-0xFE02CFFF
IRQ Channel IRQ 20
Driver f:\windows\system32\drivers\nvata.sys (5.10.2600.0666 built by: WinDDK, 98.38 KB (100,736 bytes), 22/09/2008 20:31)



am i righ in thinking this should be edited to this?

09 F9 09 70

Edited by madnlooney, 18 December 2008 - 01:52 PM.


#12 skyliner33

skyliner33

    X-S Enthusiast

  • Members
  • 5 posts

Posted 24 December 2008 - 02:44 AM

QUOTE(madnlooney @ Dec 19 2008, 12:11 AM) View Post

is it possible to get some help too? i would like to know how to work out the hex editing then i can do mine and help others. here is my information and hddhackr doesnt detect my WD1200bevs
Name Standard Dual Channel PCI IDE Controller
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCI\VEN_10DE&DEV_0265&SUBSYS_81BC1043&REV_A1\3&2411E6FE&0&68
I/O Port 0x0000FD00-0x0000FD0F
Driver f:\windows\system32\drivers\pciide.sys (5.1.2600.0 (XPClient.010817-1148), 3.25 KB (3,328 bytes), 03/08/2004 13:00)

Name Primary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&F2CF138&0&0
I/O Port 0x000001F0-0x000001F7
I/O Port 0x000003F6-0x000003F6
Driver f:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 03/08/2004 13:00)

Name Secondary IDE Channel
Manufacturer (Standard IDE ATA/ATAPI controllers)
Status OK
PNP Device ID PCIIDE\IDECHANNEL\4&F2CF138&0&1
I/O Port 0x00000170-0x00000177
I/O Port 0x00000376-0x00000376
Driver f:\windows\system32\drivers\atapi.sys (5.1.2600.5512 (xpsp.080413-2108), 94.25 KB (96,512 bytes), 03/08/2004 13:00)

Name NVIDIA nForce 430/410 Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_0266&SUBSYS_81BC1043&REV_A1\3&2411E6FE&0&70
I/O Port 0x000009F0-0x000009F7
I/O Port 0x00000BF0-0x00000BF3
I/O Port 0x00000970-0x00000977
I/O Port 0x00000B70-0x00000B73
I/O Port 0x0000F800-0x0000F80F
Memory Address 0xFE02D000-0xFE02DFFF
IRQ Channel IRQ 23
Driver f:\windows\system32\drivers\nvata.sys (5.10.2600.0666 built by: WinDDK, 98.38 KB (100,736 bytes), 22/09/2008 20:31)

Name NVIDIA nForce 430/410 Serial ATA Controller
Manufacturer NVIDIA Corporation
Status OK
PNP Device ID PCI\VEN_10DE&DEV_0267&SUBSYS_81BC1043&REV_A1\3&2411E6FE&0&78
I/O Port 0x000009E0-0x000009E7
I/O Port 0x00000BE0-0x00000BE3
I/O Port 0x00000960-0x00000967
I/O Port 0x00000B60-0x00000B63
I/O Port 0x0000F300-0x0000F30F
Memory Address 0xFE02C000-0xFE02CFFF
IRQ Channel IRQ 20
Driver f:\windows\system32\drivers\nvata.sys (5.10.2600.0666 built by: WinDDK, 98.38 KB (100,736 bytes), 22/09/2008 20:31)
am i righ in thinking this should be edited to this?

09 F9 09 70



Close tongue.gif . But your looking for the string that has the last numbers 7, and from that u get the last 4 digits of the code BEFORE the hyphen. i.e. For the SATA controller on IRQ Channel 23, the code would be
09 F0 09 70
And for your other Sata controller it would be 09 E0 09 60

Have you been following the tutorial here? http://forums.xbox-s...howtopic=660096 It explains how to everything.
Basically u need open up hddhckr in a hex editor (i use win hex, it's pretty easy to use), scroll down to the last string, which is 6F 72 74 3D 4D 50 52 54 and replace 4D 50 52 54 with, in your case 09 F0 09 70. Save it, then copy that edited hddhckr to your bootable floppy/flash drive.
What i did was disconnect everything bar a power and data feed for the WDBEVS. Plug it into SATA port 0 or 1.
Power up your pc and enter your bios settings, change your SATA controller settings to legacy mode if you can.
Save settings and exit, then resume process as normal. If it still doesn't detect, try the other port 0 or 1. If you're still having no luck (don't forget to change bios settings back to normal if OS doen't load) , go into a hex editor again and change the last string again 4D 50 52 54 if you opened up the original hddhckr or
09 F0 09 70 if you're changin the already edited one, and change the code to 09 E0 09 60. save and exit, copy it to your bootable device.
Same deal, check Bios settings and make sure WDBEVS is the only thing plugged in, try SATA 0 and 1.

Hope that helps.
Lettuce know how you go.

#13 0o0o0o

0o0o0o

    X-S Enthusiast

  • Members
  • 8 posts

Posted 11 January 2009 - 09:08 AM

I've been researching and trying for hours and I'm completely stuck!

Here's the data from msinfo32 --> components\storage\SCSI

QUOTE
Name Intel® ICH8R/ICH9R SATA RAID Controller
Manufacturer Intel
Status OK
PNP Device ID PCI\VEN_8086&DEV_2822&SUBSYS_2A6F103C&REV_02\3&11583659&0&FA
I/O Port 0x0000B880-0x0000B887
I/O Port 0x0000B800-0x0000B803
I/O Port 0x0000B480-0x0000B487
I/O Port 0x0000B400-0x0000B403
I/O Port 0x0000B080-0x0000B09F
Memory Address 0xFE8FF000-0xFE8FF7FF
IRQ Channel IRQ 19
Driver c:\windows\system32\drivers\iastor.sys (7.8.0.1012, 301.02 KB (308,248 bytes), 8/10/2008 5:25 AM)

Name AYCLX86R IDE Controller
Manufacturer (Standard mass storage controllers)
Status OK
PNP Device ID ACPI\PNPA000\4&5D18F2DF&0
I/O Port 0x0000FFE0-0x0000FFEF
IRQ Channel IRQ 9



So, I've read the readme.txt included w/ hddhackr, read several threads (including the ones linked to on this thread), compared other examples to verify my logic, and I'm still stuck!

If I'm not mistaken, I want to work with the addresses from the 1st and 3rd I/O Ports listed in msinfo32:
#1) 0x0000B880-0x0000B887
#3) 0x0000B480-0x0000B487

This thread says to use the ones ending with 7's, and the hdd hacker readme says it should be the ones with a difference of 7. Either way indicates these 2 I/O ports --> They both end with 7, and the difference within the addresses before and after the hyphen is 7 too.

So, I hex edited the last 4 bits in hddhackr as follows:
Original = 4D 50 52 54 CHANGED TO
For my Intel ICH8R/ICH9R = B8 80 B4 80


I copied over the hddss.bin and my edited version of hddhackr.com to a floppy boot disk, shut down, removed all drives from SATA, plugged in my WD1200bevs as the one and only SATA device plugged in, and booted from the floppy.

hddhackr still won't detect my hdd!

I've tried different SATA connections to my mobo, and also some recommendations for other ICH8R/ICH9R SATA controllers that I've seen on this and other threads (D8 80 D4 80, C8 80 C4 80). No dice. I even tried on a different computer, but it wouldn't work either. I can't figure out what the code should be on the other comp b/c it doesn't display the I/O data in msinfo32 under either SCSI or IDE.

uhh.gif uhh.gif uhh.gif PLEASE HELP!!! uhh.gif uhh.gif uhh.gif


#14 0o0o0o

0o0o0o

    X-S Enthusiast

  • Members
  • 8 posts

Posted 12 January 2009 - 02:40 AM

Per the recommendation of a response on another forum, I also tried replacing the last 4 bits with I/O's for #1 and #3 seperately: B8 80 B8 87 and B4 80 B4 87. Tried it on every SATA port I have. Also retried what I first thought would be correct (B8 80 B4 80), on every SATA port, shutting down between each swap.

I'm pretty certain now that the Intel ICH8R/ICH9R SATA controller on the Asus IPIBL-LB motherboard (on most HP Pavillion models from 2008) is incompatible with HddHackr. If anybody else can confirm or deny, please do, but I actually understand what I'm doing with the hex editor and it just doesn't work.

Anyway, I just ordered a PCI to SATA card with the VIA 6421A SATA chipset. Since pretty much everybody (who doesn't already have SATA that works for 360 purposes) uses this, it's gotta work. cool.gif

#15 skyliner33

skyliner33

    X-S Enthusiast

  • Members
  • 5 posts

Posted 18 January 2009 - 03:40 AM

Yea that sucks it didn't work in the first place. I had a heap of trouble with this as well, but everything i did, i posted up. U didn't mention that you checked your BIOS settings, that's an important step as well. I also have the Via 6421 card as well. Comes in handy for other things as well. Check the I/o's for that card as well, if you're still having trouble detecting in hddhckr




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users