Faulty Guitar Hero 3 Guitar?
Posted 02 November 2007 - 08:43 PM
Well, as the story goes, I purchased Guitar Hero 3 for the Xbox 360 on Wednesday. Being impressed by the guitar's sheer sexiness, I was ready to rock it out. But, to my dismay, my yellow button was unresponsive!
After some troubleshooting, I came to the realization that the fret board (the long black shaft with the green, red, yellow, blue, and orange buttons) was a little loose. So, as any xbox-scene member would do, I took it apart! Some of my findings will come later in this tutorial, as I believe them to not be the direct cause of unresponsive buttons; I don't want to confuse anyone.
Without further ado, my Guitar Hero 3 Guitar Fix
* Please ignore my lack of proper guitar vocabulary *
Guitar Hero 3 Guitar
T8 bit (I think that's the size)
Removing the fret board from the guitar:
This step is very simple. Simply flip the guitar over and push the lever from one side to the other (left to right.. up to down.. depends how you're looking at it). This will unlock the fret board, allowing you to pull the fret board away from the guitar.
Unscrewing 2 screws:
In this step, you remove 2 screws using your T8/torx driver. They're located here-
How the fret board/guitar works:
Basically, there's a green PCB (Printed Circuit Board) on the end of the fret board with 8 "golden" points. In the receiving end of the guitar, there are 8 metal pins. When the fret board is inserted into the guitar, the 8 metal pins in the guitar make contact with the 8 "golden" points on the fret board. We'll be working with the green PCB.
Finding the "tabs":
Basically, the green PCB is secured by 4 tabs. There are tabs in the bottom left corner, bottom right corner, upper left corner, and upper right corner. What were gonna do is move the PCB IN FRONT of the tabs. By "in front," I mean in the direction of the guitar (if it were being inserted into the guitar) The tabs are indicated by the red arrows-
Moving the PCB:
So here comes the actual fix. Since you already removed the screws in step 2, all you have to do is carefully pry the 2 halves the fret board open. As in, grab the "top" of the fret board and pull it upwards; Grab the "bottom" of the fret board and pull it downwards (This may be easier to do with just 1 hand, seeing as how you'll need the other). With your free hand, grab/finagle/move the green PCB in front of the tabs. I found it easier to do the "bottom" of the green PCB first, then do the "top." It should look like this-
*Notice- the tabs are no longer present because they're located behind the green PCB*
Putting the fret board back together:
Now that the green PCB is in its new position, make sure the fret board is securely and properly closed. Now take the 2 screws from earlier that you removed and screw them back in. Now slide the fret board into the guitar, kick on your 360, and test it out!
IF this doesn't work, you may want to completely take apart the fret board and take a look at the wiring inside. I found this-
Although it looks as if the "pins" are strategically placed, I'd double check.. perhaps even remove the wiring from them to get this-
Well, that's all I got. I surely hope I've been of help!
Enjoy rocking it out with your fixed guitar!
Posted 03 November 2007 - 03:13 PM
Posted 04 November 2007 - 06:17 AM
Posted 05 November 2007 - 12:40 AM
I thought from day 1 that the detachable neck was a bad idea. What exactly were they thinking? My intention was to possible just hard wire the sucker. I think I'll start first here.
Posted 05 November 2007 - 12:49 AM
Posted 05 November 2007 - 02:18 AM
Posted 05 November 2007 - 03:29 AM
Maybe they will make addon necks in the future? Something to make the guitar look different
That would be awesome
Posted 07 November 2007 - 04:41 AM
And holy crap to the amount of views this thread has gotten! Almost 8000 in just a few days!
I agree with commandersafi.. new/custom necks would be friggin' sweet!
Posted 07 November 2007 - 05:57 AM
Posted 07 November 2007 - 07:44 PM
Posted 08 November 2007 - 07:51 PM
And I am very pleased with the results
Just two things I'd add, for novices like myself who want to do this:
Use a T10 torx screwdriver bit, not T8. A full set cost me $12 at Lowe's, you can prolly find one cheaper!
Take out the first four screws instead of just the first two, it'll give you a little more room to do it.
Now the neck fits tightly with the body, doesn't budge, and plays perfectly! I'm so happy! Thanks for posting this!
Posted 08 November 2007 - 09:05 PM
Removing more screws is fine.. I just did the minimal amount.
I'm glad it worked out for you! Have fun being a rock star!
Posted 09 November 2007 - 04:21 AM
Edited by Birdy2k2, 09 November 2007 - 04:23 AM.
Posted 15 November 2007 - 06:04 PM
Does anyone see this as an issue?
Im curious if to much stress is being put on the pins, since the guitar neck is very tight. I had to press pretty hard to lock it in.
Posted 16 November 2007 - 12:39 AM
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users