1 TB SATA Hard Drive Upgrade
Posted 24 May 2008 - 11:30 AM
I installed a WD10EACS 1TB drive into a 1.0 xbox a little while ago, along with one of those Sabrent type IDE -SATA converters I found on ebay:
My problem seems to be the same as others are reporting, it seems to work ok most of the time, but sometimes hangs when booting, or boots very slowly.
When it does boot, sometimes it works ok, other times, after booting to the slayers menu, if you try and load xbmc or a game, it starts to load then goes back to the slayers menu. Rebooting it usually makes it work.
Other times I was able to ftp around 500GB to it without any problems.
Does anyone whow what the jumpers on the converter board are for ? Mine came with the holes on the board, but no pins. I soldered in the 4 pins and tried a jumper in the 2 positions but doesn't seem to have helped. It must be some sort of timing issue ?
I bought 2 of these converters at the same, I'll try the other one with the 1TB drive in a 1.6 xbox and see what happens...
Posted 24 May 2008 - 11:43 AM
Posted 25 May 2008 - 03:37 AM
Posted 25 May 2008 - 09:37 AM
Is this thread just to see if the 1Tb can be successfully used INSIDE the xbox with no corruption.
Posted 26 May 2008 - 07:31 PM
I noticed the adapter is listed as ATA 100/133, I take it you guys are using an 80 wire IDE cable? I've had similar problems on some older pc's with using 100/133 drives with 40 wire (ata 66) cables. Maybe the adapter is picky......
Hope this helps and I'm not just pointing out the obvious
Edited by zx6r6, 26 May 2008 - 07:32 PM.
Posted 26 May 2008 - 09:17 PM
But beware that the xbox is not fully compatable with a nearly full 750GB hdd. I have around 200 gigs free on my 750gb HDD but folders and files float around the F & G drive mysteriously. One day something will be on your F drive, and the next day it appeared on the G drive~!!
Its not exactly that dramatic but just beware, the partitioning acts goofy sometimes. But in all reality i have not lost any data yet on my xbox so you should be alright.
Just make sure that:
Your bios supports custom partitions
You split F & G evenly in space
Set the entire hard drive to 32k clusters!
Posted 29 May 2008 - 03:09 AM
So I've been working on this for a few weeks when I get some time away from work and the social life.
This is what I've tried thus far (in no particular order):
- Variety of jumper settings on the Sabrent Adapter, including using 2 jumpers! (currently have the jumper completely removed)
- Fully disassembled and cleaned the MB and all components of my Xbox.
- Re-soldered the 2 main pins for the power connector on my PSU (I have a 1.0 and it needed to be done anyhow)
- Checked over all of my mod chip soldering work and cleaned it up a bit (I've gained some soldering skills in the last year or so!)
- Checked all cable connections
- Tried a variety of settings:
-Tried all of the Acoustic Management options for my HD (Samsung 750gig)
-Tried different power management settings in XBMC for the HD
-Set the HD's link speed to 1.5 rather than 3.0 using Samsung's Speed Switcher Utility
- Turned off the DVD check in the X3 bios
- Tried (re)booting in a variety of ways:
-CD/DVD in or out
-IR Remote Dongle in/out
-Wired/Wireless controllers in/out
-Others I'm probably forgetting
So, none of this stuff seems to make a bit of difference. Very frustrating! And today I noticed another peculiar problem. It seems that I can copy files from my SMB share with no problem, but when I tried to move a folder with files in it from my G to my F, I kept getting file copy errors! XBMC would stop the copy and give some error message about failing to copy. I tried quite a few times before giving up and just using the SMB file transfer instead.
And here's something else I noticed today. This Sabrent adapter seems to me to be the exact same adapter as this Rosewill one:
And, after reading all of the reviews for both the Sabrent and Rosewill models, it seems that people have had a variety of problems with both. From them not working at all, to the same slow boot / no boot problem, even on a pc.
So, since I've sorta hit a wall with all this, I broke down and have ordered another adapter. I had to search high and low for another model and supplier that seemed like it would do the job. I will report back with any success/failures after I've had a chance to fully test it.
capboy210: Is it necessary to set ALL partitions to 32k clusters? I've been under the impression that only the large partitions need it?
Posted 29 May 2008 - 03:50 AM
Only partitions larger then 256gb need to use larger clusters. I'm not even sure if the console would function if you did the entire drive that way.
Posted 03 June 2008 - 03:57 AM
SO, a couple days ago my month old 750 gig SATA Samsung HD started the good ole "click of death". Of course, it's hard to say what exactly caused this. Heat? The SATA adapter? Samsung's new substandard HD's?
I read over the reviews for this particular model a little more closely than when I had impulsively bought the drive a month ago. It seems at least a few people have had the same problem or a DOA drive. I even read one review that said "I used to have great luck with Samsung" (paraphrasing). I've come to the same conclusion. I have Samsung drives that are a few years old running 24/7 and have never had a problem (SATA too). THANK GOD that Newegg is so freakin awesome. I was just past the 30 day mark, but I emailed them and they emailed me a prepaid UPS label and authorized the RMA!
Luckily, I hadn't reformated my old 300 gig Xbox HD, so I only lost a few things added over the last month.
Aside from all this, I intended to order a new SATA adapter from some no-name Yahoo shop, but they canceled the order and notified me they were out of stock. It "looked" like a higher quality adapter from the pictures. It has a JMicron JM20330 chipset and the store is kind enough to have a lot of info about the product:
BUT, no stock, so I ordered a similar looking one from an Ebay Store:
Paid $7.98 WITH shipping!! Which is great, but I looked over it real close and noticed some horrible soldering work. And as usual, it's made in freakin China. Also, it has a 2X2 set of jumper pins, but no jumper included or any indication of how they would work. And the packaging RAPES the english language. Which is as funny as always, but I'm sure my heart will stop for a second the first time I try to use it.
So now I have a new Samsung HD on the way and 2 SATA adapters to experiment with.
Of course I will report back here with the results...
Posted 12 June 2008 - 03:04 AM
I wouldn't at all be surprised that these little SATA adapters are hit and miss though, they don't exactly look like top notch engineering... But my particular one is solid so far.
ps. Im using the standard 40 pin IDE cable btw, but from my past experiences with xboxen 40/80 pin doesnt matter, as long as the cable is sound.
Posted 12 June 2008 - 03:18 AM
Sometimes when it does this, if I wait a while (10 - 15 minutes) with it powered on it will actually start up (its kinda spooky, no idea what it is doing during all that time as there is no activity at all). Other times it just wont boot, even when I let it sit for hours. I generally open it up, look at everything, find nothing wrong, and then when I plug it back in everything is fine again... Im only posting this because I have spoke to friends with 1.0s and quite a few of them have dodgy ones as well. Id love to fix it though, as that is why I didn't put the 1TB in it. If I thought I could trust it Id put a 1TB in it as well. As it is now, Ill probably just buy another 1.6, they are like $60 or so on ebay...
Posted 12 June 2008 - 05:21 AM
BUT, no stock, so I ordered a similar looking one from an Ebay Store:
I'm also using that adapter for my 2.5" 320gb samsung spinpoint. I can't test it out now as I am waiting on a new power supply, but I will let you know how it turns out.
Posted 13 June 2008 - 08:57 PM
I'm posting this because someone else mentioned they ran out of willing testers for 64Kb clusters. Well you definitely have one now. I just ordered a new v1.1 board to replace my 1.0. I'm going to TSOP flash it with x2 5035 and am going to buy the same 1TB driver/adapter for it as well. I would REALLY like to try and get it working with 1 F partition (or a small F and a > 512GB G), because from my understanding unlike a softmod the X2 bios wont let you do an even split of the free space between F and G for very large drives (please correct me if I'm wrong on this). Even if it is possible to split though, my preference is to have one of the partitions be > 512GB. I store nothing large media files (nothing smaller than 500MB or so) on it so I don't much care about slack.
When I get everything in order I will post again, but if anyone has info on how I can get my hands on the version of xbpartitioner that supports 64KB clusters please let me know. I know there has been alot of activity on a patch set for it lately, but I havent seen it on xbins or anything.
Posted 19 June 2008 - 08:38 PM
Well, I got the replacement Samsung HD. As soon as I started to transfer my stuff from my old HD I started having problems! Freezing during transfers and slow/no boots.
I'm pretty sure that it is only a problem with the HD's themselves. I cannot return the drive for another Brand/Model so I am stuck getting it exchanged AGAIN.
Well at least Newegg makes this painless for me with free shipping and friendly service.
So now I have to wait for another replacement drive and hope that it won't crap out on me right away. Then I get to worry about it crashing some time over the next year and losing all my stuff. GREAT!!
This whole upgrade has gone so well!! Screw you Samsung!! I used to trust you!
BTW, I was running this replacement drive on the new SATA adapter I bought from Ebay.
Posted 22 June 2008 - 01:53 PM
I then tried an identical adapter I bought with the other one as a spare - this time both xboxes worked perfectly every time.
I checked the faulty adapter with a magnifying glass and found a solder bridge between 2 of the legs on the main chip on the board. This isn't present on the good one. I haven't been able to remove it yet to test, but the seller on ebay has offered to send a replacement anyway. due to the gap between the legs, the short is barely visible to the naked eye.
The soldering on these boards (even the one that works) is quite dodgy, and wouldn't be surprised if there are many more out there with similar faults. They are probably all made in the same Chinese factory no matter what brand name is on them.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users