Jump to content


Photo

Wiikey Pin 6


  • Please log in to reply
10 replies to this topic

#1 bigjay8510

bigjay8510

    X-S Senior Member

  • Members
  • PipPip
  • 182 posts
  • Location:Las Vegas, NV
  • Xbox Version:v1.5
  • 360 version:v1 (xenon)

Posted 05 August 2008 - 06:57 PM

I finished all the other points, but I messed up pin 6 is there an alternate point for pin 6?

#2 swampy1111

swampy1111

    X-S X-perience

  • Members
  • PipPip
  • 346 posts

Posted 06 August 2008 - 01:10 PM

follow the track on the board to the ic chip and solder it directley to the leg if i remember correctley it goes to leg number 8 as you count them up but please check, i haven done a wiikey for a while

#3 bigjay8510

bigjay8510

    X-S Senior Member

  • Members
  • PipPip
  • 182 posts
  • Location:Las Vegas, NV
  • Xbox Version:v1.5
  • 360 version:v1 (xenon)

Posted 06 August 2008 - 05:20 PM

does this right? i wasn't sure if this was it because these are different solder points

IPB Image

#4 swampy1111

swampy1111

    X-S X-perience

  • Members
  • PipPip
  • 346 posts

Posted 06 August 2008 - 09:29 PM

QUOTE(bigjay8510 @ Aug 6 2008, 05:56 PM) View Post

does this right? i wasn't sure if this was it because these are different solder points

IPB Image



yes thats right its the eighth pin from the right
when you say these are differrent solder points do you mean youve used alternative ones

#5 bigjay8510

bigjay8510

    X-S Senior Member

  • Members
  • PipPip
  • 182 posts
  • Location:Las Vegas, NV
  • Xbox Version:v1.5
  • 360 version:v1 (xenon)

Posted 07 August 2008 - 01:51 AM

the different solder points that i use where the ones according to this guide...

http://www.ps2cover....nstallation.pdf

what happened was i got sloppy when soldering pin 6 and basically there is no solder left on pin 6 (not on the wiikey on the board). so can i just run pin 6 from the wiikey to leg 8 on the ic chip?

#6 bigjay8510

bigjay8510

    X-S Senior Member

  • Members
  • PipPip
  • 182 posts
  • Location:Las Vegas, NV
  • Xbox Version:v1.5
  • 360 version:v1 (xenon)

Posted 07 August 2008 - 05:42 AM

i wired to the ic chip (pinout 8) when i turn on the wii everything is fine, but the dvd drive is not spinning up. i have checked al the connections...

#7 swampy1111

swampy1111

    X-S X-perience

  • Members
  • PipPip
  • 346 posts

Posted 08 August 2008 - 01:10 PM

if the drive is not spinning up its 99% the install .... check all the connections with a test meter and a good magnyfying glass

#8 bigjay8510

bigjay8510

    X-S Senior Member

  • Members
  • PipPip
  • 182 posts
  • Location:Las Vegas, NV
  • Xbox Version:v1.5
  • 360 version:v1 (xenon)

Posted 25 August 2008 - 08:27 PM

I connected pin six to the 8th leg with some small wire and its working like a champ.

#9 swampy1111

swampy1111

    X-S X-perience

  • Members
  • PipPip
  • 346 posts

Posted 26 August 2008 - 03:12 PM

glad to help m8

#10 DimitroffVodka

DimitroffVodka

    X-S Enthusiast

  • Members
  • 4 posts

Posted 06 September 2008 - 12:18 AM

So Happy I came upon this thread. I did the same thing but on point 3. What guage wire did you use to solder on the IC chip?

#11 swampy1111

swampy1111

    X-S X-perience

  • Members
  • PipPip
  • 346 posts

Posted 06 September 2008 - 04:12 PM

use 30swg kaynar




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users