Jump to content


Photo

1 Green Light


  • Please log in to reply
10 replies to this topic

#1 SavageCHRIS

SavageCHRIS

    X-S Enthusiast

  • Members
  • 20 posts
  • Xbox Version:v1.6
  • 360 version:v1 (xenon)

Posted 08 December 2009 - 02:06 PM

I have 2 perfect dumps of my nand so i extracted my keyvault and config and injected them into XBR_Xenon_8955_1.bin but when i flash it all i get is a solid green light in the middle and a blank screen, I have been searching and found if people don't inject their keyvault it can cause christmas lights, I definitely have an exploitable kernal so i don't know what to do, any help will be much appreciated, thanks

#2 SavageCHRIS

SavageCHRIS

    X-S Enthusiast

  • Members
  • 20 posts
  • Xbox Version:v1.6
  • 360 version:v1 (xenon)

Posted 08 December 2009 - 06:22 PM

I didn't realise there was a XBR_Xenon_1921_8955_1.bin so i flashed that and i booted in to XBReboot but the fans started spinning fast so i turned it off and put it back in its metal case and turned it back on and now it just shows the green light again while the fans are spinning fast, I don't understand how the green light can be showing now as i have booted in to xbreboot so i must have flashed it fine, please help.

#3 Vejita

Vejita

    X-S Expert

  • Members
  • PipPipPip
  • 671 posts
  • Xbox Version:v1.3
  • 360 version:v4.0 (jasper)

Posted 08 December 2009 - 06:35 PM

Try flashing XBR without the config block so only inject your KV and see what happens.

#4 SavageCHRIS

SavageCHRIS

    X-S Enthusiast

  • Members
  • 20 posts
  • Xbox Version:v1.6
  • 360 version:v1 (xenon)

Posted 08 December 2009 - 06:56 PM

I think I figured it out, I messed round with the jtag wiring and it booted into the dash board then I tried xell and it worked, now I'm getting E79 so its obviously the wiring ill resolder and hopefully ill get it working.

#5 Tj1zzle

Tj1zzle

    X-S Member

  • Members
  • Pip
  • 102 posts
  • Xbox Version:unk
  • 360 version:unknown

Posted 08 December 2009 - 10:51 PM

howd everything work out for u?
cuz ive got similar probs when flashing back my original dump.

#6 vintage_guitar

vintage_guitar

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,441 posts
  • Xbox Version:v1.4
  • 360 version:unknown

Posted 08 December 2009 - 10:53 PM

QUOTE(Tj1zzle @ Dec 8 2009, 03:51 PM) View Post

howd everything work out for u?
cuz ive got similar probs when flashing back my original dump.

Could be wiring, bad blocks?

Edited by vintage_guitar, 08 December 2009 - 10:54 PM.


#7 manu07

manu07

    X-S Member

  • Members
  • Pip
  • 89 posts

Posted 08 December 2009 - 11:17 PM

QUOTE(Tj1zzle @ Dec 8 2009, 04:51 PM) View Post

howd everything work out for u?
cuz ive got similar probs when flashing back my original dump.


me too i got one green light nothing on screen. how do i load the boatloader ? do i put a controller in the rear usb port does it matter if its a play and charge cable cause i dont have any wired controllers? i tried flashing back the orginal nand and now i get 3 red rings

#8 Tj1zzle

Tj1zzle

    X-S Member

  • Members
  • Pip
  • 102 posts
  • Xbox Version:unk
  • 360 version:unknown

Posted 09 December 2009 - 12:22 AM

QUOTE(manu07 @ Dec 8 2009, 05:17 PM) View Post

me too i got one green light nothing on screen. how do i load the boatloader ? do i put a controller in the rear usb port does it matter if its a play and charge cable cause i dont have any wired controllers? i tried flashing back the orginal nand and now i get 3 red rings

you mean xell? then yes. and play charge is ok
and for ur original dash u need to remover jtag resistors, thats prolly why u get red lights

#9 vintage_guitar

vintage_guitar

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,441 posts
  • Xbox Version:v1.4
  • 360 version:unknown

Posted 09 December 2009 - 12:25 AM

QUOTE(Tj1zzle @ Dec 8 2009, 05:22 PM) View Post

for ur original dash u need to remover jtag resistors, thats prolly why u get red lights

not true. mine boots up with them connected

#10 Tj1zzle

Tj1zzle

    X-S Member

  • Members
  • Pip
  • 102 posts
  • Xbox Version:unk
  • 360 version:unknown

Posted 09 December 2009 - 12:51 AM

QUOTE(vintage_guitar @ Dec 8 2009, 06:25 PM) View Post

not true. mine boots up with them connected


ok then its semi not true b.c it is most definately an issue for others

#11 SavageCHRIS

SavageCHRIS

    X-S Enthusiast

  • Members
  • 20 posts
  • Xbox Version:v1.6
  • 360 version:v1 (xenon)

Posted 09 December 2009 - 02:42 AM

I resoldered my jtag wires and now everything works fine




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users