Jump to content


Photo

Fix E74, Heatgun Method Still Not Work


  • Please log in to reply
9 replies to this topic

#1 mrghandi

mrghandi

    X-S Enthusiast

  • Members
  • 11 posts

Posted 12 December 2009 - 09:04 AM

could someone help me with error e74

i already using heatgun n overheat method but it still show e74...
i didn't do xclamp fix, so it's original xclamp from microsoft

could someone help me with my problem

#2 xboxmods2977

xboxmods2977

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,156 posts
  • Xbox Version:v1.0
  • 360 version:none

Posted 12 December 2009 - 09:14 AM

The ORIGINAL XBOX did not have an e74 error. If you are inquiring about the Xbox 360, your post may get more attention in the 360 section.

Edited by xboxmods2977, 12 December 2009 - 09:16 AM.


#3 mgeno216

mgeno216

    X-S Member

  • Members
  • Pip
  • 126 posts
  • Location:Wheaton, Illinois
  • Xbox Version:unk
  • 360 version:v3.0 (falcon)

Posted 12 December 2009 - 06:59 PM

Reflow the GPU again and if that doesn't work try and reflow the RAM chips. Very rarely the does it lie in the ram, but it is still possible. If that doesn't work you may need a reball. If it comes to that pm and i will give you the name of a good guy.


#4 mrghandi

mrghandi

    X-S Enthusiast

  • Members
  • 11 posts

Posted 14 December 2009 - 10:08 AM

QUOTE(mgeno216 @ Dec 12 2009, 07:59 PM) View Post

Reflow the GPU again and if that doesn't work try and reflow the RAM chips. Very rarely the does it lie in the ram, but it is still possible. If that doesn't work you may need a reball. If it comes to that pm and i will give you the name of a good guy.



yes, I've done reflow the GPU, RAM CHIP, CHIP ANA several times, but the result is the same, still appear E74 ... I'm Indonesian, I have heatgun like this IPB Image What may be less hot ..??? I have been heating the GPU, RAM, ANA for about 5 minutes with the highest heat level ..... sorry my english not good

#5 under420dog

under420dog

    X-S X-perience

  • Members
  • PipPip
  • 470 posts
  • Location:Lake Geneva,WI
  • Interests:anything....
  • Xbox Version:unk
  • 360 version:unknown

Posted 14 December 2009 - 10:57 AM

did you even check if the video cable was ok?
and worry more about the GPU/ANA HANA area top and bottom.....top first till you see the solder shining....
check it...then do the bottom.....make sure you let it cool at least 1/2 hour before switching fro top to bottom..

Edited by under420dog, 14 December 2009 - 10:57 AM.


#6 mrghandi

mrghandi

    X-S Enthusiast

  • Members
  • 11 posts

Posted 14 December 2009 - 11:46 AM

QUOTE(under420dog @ Dec 14 2009, 11:57 AM) View Post

did you even check if the video cable was ok?
and worry more about the GPU/ANA HANA area top and bottom.....top first till you see the solder shining....
check it...then do the bottom.....make sure you let it cool at least 1/2 hour before switching fro top to bottom..




Do I need a flux ..??? I have 3 times to heat the GPU, ANA, RAM, but the bottom was 1 time I reheat, there is another solution ..??

#7 under420dog

under420dog

    X-S X-perience

  • Members
  • PipPip
  • 470 posts
  • Location:Lake Geneva,WI
  • Interests:anything....
  • Xbox Version:unk
  • 360 version:unknown

Posted 14 December 2009 - 12:03 PM

yes time for someone to go over the board and troubleshoot it...and then a re-ball as said....

#8 mrghandi

mrghandi

    X-S Enthusiast

  • Members
  • 11 posts

Posted 15 December 2009 - 08:49 AM

QUOTE(under420dog @ Dec 14 2009, 01:03 PM) View Post

yes time for someone to go over the board and troubleshoot it...and then a re-ball as said....


thank's for before...
after reflow the gpu, now my xbox is showing 0102, i have using the methode to fix the 0102 problem but it still didn't work!
what should i do next??

#9 under420dog

under420dog

    X-S X-perience

  • Members
  • PipPip
  • 470 posts
  • Location:Lake Geneva,WI
  • Interests:anything....
  • Xbox Version:unk
  • 360 version:unknown

Posted 15 December 2009 - 01:12 PM

heat it back up....what's the temps that station puts out?


#10 mrghandi

mrghandi

    X-S Enthusiast

  • Members
  • 11 posts

Posted 15 December 2009 - 03:11 PM

QUOTE(under420dog @ Dec 15 2009, 02:12 PM) View Post

heat it back up....what's the temps that station puts out?


it's 300c max




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users