Jump to content


Photo

Some Success For Jasper... 256


  • Please log in to reply
9 replies to this topic

#1 ahmer

ahmer

    X-S Member

  • Members
  • Pip
  • 144 posts

Posted 25 January 2010 - 09:15 PM

AS some of you may know I have been all over trying to flash my jasper 256. I have flashed before and wasnt a complete NOOB, using the same pc set up and wiring, i couldnt get the right flash config, Error reading block. After days of soldering and re soldering. I got the right flash config, and it reads for ten min or so, and then the reading block errors start,

How can I build on this success ?

Do i have to read the entire 256 ? (nandpro lpt: -r256 jasper.bin )

thanks i got the right config on my last try, right before i was about to call it quits, now i have new life....

#2 Looouky

Looouky

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,060 posts
  • Location:Calgary, Alberta Canada
  • Xbox Version:v1.4
  • 360 version:v1 (xenon)

Posted 25 January 2010 - 09:29 PM

only the first 70mb, hmm I would use my guide here on flashing with xellous but I am not sure if I would proceed if your getting errors after 10 min. What is the error your getting.

Here is my link to my guide:

http://docs.google.c...fmv5h_0hbhwdzfv

It has all the commands for 256.

Discuss here:
http://forums.xbox-s...howtopic=703757

Now with my method you never read or write for more then 5mins. So you should be able to do it, but that up to you if you want to proceed.

Edited by Looouky, 25 January 2010 - 09:33 PM.


#3 ahmer

ahmer

    X-S Member

  • Members
  • Pip
  • 144 posts

Posted 25 January 2010 - 11:26 PM

it only reads the first 10 blocks or soo

after that i get error reading block 0 on all the rest of them


it was so hard getting it to this point that I dont think its a good idea to play with the wireing agin. I lilltery had to get the wires down to 3 inches...

its actually becoming very spntanious, Im thinking another connectiong soldering error, but if that was the case then why when i start it back up it goes detects ok.

Sometimes it can read for 5 min, sometimes 5 seconds before getting an error. Sigh, this is becoming a nightmare of a process.

Edited by ahmer, 25 January 2010 - 11:18 PM.


#4 omega232

omega232

    X-S Member

  • Members
  • Pip
  • 66 posts

Posted 25 January 2010 - 11:58 PM

Might be time to shell out for a multimeter and check your soldering, only time i've really seen that error is with a bad connection somewhere.

#5 ahmer

ahmer

    X-S Member

  • Members
  • Pip
  • 144 posts

Posted 26 January 2010 - 12:04 AM

i have one, Ive tested the wires before this attempt but not on this one, I will give it a go..

#6 ahmer

ahmer

    X-S Member

  • Members
  • Pip
  • 144 posts

Posted 26 January 2010 - 12:24 AM

multi meter test is positive for all connections going to the male side of db 25

wud flux on mobo cause problems
?

Edited by ahmer, 26 January 2010 - 12:39 AM.


#7 Looouky

Looouky

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,060 posts
  • Location:Calgary, Alberta Canada
  • Xbox Version:v1.4
  • 360 version:v1 (xenon)

Posted 26 January 2010 - 08:10 AM

Upload pictures of your soldering maybe we can see something your missing.

#8 ahmer

ahmer

    X-S Member

  • Members
  • Pip
  • 144 posts

Posted 26 January 2010 - 11:14 AM

got it to read, had to use a different pc, doesnt make sense as this is the pc I used to flash a xenon, but jasper wont.. who knows prob is, The pc that i tried on is a work pc, and I used it to test, but I cant sit there with my xbox running a 12 hour dump of 256mb nand ? any suggestions as to how I can pull this off ?

#9 dakaku

dakaku

    X-S Senior Member

  • Members
  • PipPip
  • 167 posts

Posted 26 January 2010 - 07:09 PM

Im just curious: Do you still try this without the 100ohm resistors ?

#10 ahmer

ahmer

    X-S Member

  • Members
  • Pip
  • 144 posts

Posted 26 January 2010 - 07:24 PM

yes even on the second pc, I didnt need resistors. I think i read somewhere that only the old pcs need resistors, both the pcs, that I have used so far, have been P4, which isnt new i know but isnt quite old either..




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users