Jump to content


Photo

250 Error At Block 8c


  • Please log in to reply
7 replies to this topic

#1 TK-101

TK-101

    X-S Senior Member

  • Members
  • PipPip
  • 207 posts
  • Xbox Version:unk
  • 360 version:v3.0 (falcon)

Posted 24 March 2010 - 07:47 PM

I have a xenon motherboard using lpt. I'm using 68 ohm resistors because my xbox could not be detected by nandpro. Im using nandpro 2.0b. My cable is around 6 inches long.

This is the 9th xbox iv done and its the only one I've had problems/errors with so i dont know what to do. uhh.gif

I've tried to read block 8c manually but i still get the same error.

Anyone got any suggestions?

#2 thwack

thwack

    X-S Freak

  • Last Chance
  • PipPipPipPipPip
  • 1,334 posts
  • Location:Yorkshire at heart.....
  • Xbox Version:unk
  • 360 version:unknown

Posted 24 March 2010 - 08:06 PM

Does it come up as reallocated in Degraded? If so, you're ok - do the do with Xellous or one of the flashing apps that reallocate for you. Otherwise, you can do it manually if you know where the blocks reallocated (ie in Degraded it'll probably be at 0X03FF).

#3 flconsoletech

flconsoletech

    X-S Enthusiast

  • Members
  • 20 posts
  • Location:FL
  • Interests:soldering, repairing things, playing games of all kinds, going to the beach, movies...
  • Xbox Version:v1.6b
  • 360 version:v5.0 (360S - trinity)

Posted 24 March 2010 - 08:21 PM

Can you just use bad block mover and relovate the block to the end? should be fine.

#4 TK-101

TK-101

    X-S Senior Member

  • Members
  • PipPip
  • 207 posts
  • Xbox Version:unk
  • 360 version:v3.0 (falcon)

Posted 24 March 2010 - 08:22 PM

It comes up with;

Note : Bad Block @ 0x41
Note : Bad Block @ 0x42
Note : Bad Block @ 0x8C
Note : Block 0x8C found at 0x3FF


Is that relocated?

#5 thwack

thwack

    X-S Freak

  • Last Chance
  • PipPipPipPipPip
  • 1,334 posts
  • Location:Yorkshire at heart.....
  • Xbox Version:unk
  • 360 version:unknown

Posted 24 March 2010 - 08:26 PM

QUOTE(TK-101 @ Mar 24 2010, 07:22 PM) View Post
It comes up with;

Note : Bad Block @ 0x41
Note : Bad Block @ 0x42
Note : Bad Block @ 0x8C
Note : Block 0x8C found at 0x3FF


Is that relocated?


Yep - 8C is - you want to dump that NAND again, or just 0X41 + 0X42 as those aren't (just in case).


#6 TK-101

TK-101

    X-S Senior Member

  • Members
  • PipPip
  • 207 posts
  • Xbox Version:unk
  • 360 version:v3.0 (falcon)

Posted 24 March 2010 - 08:48 PM

Just read nand again with no success. Just tried the block mover and it says:

Found Block ID 0x008C at offset 0x0107BE00
== Analyzed successfully ===========================
Erasing 0x20 Spare Blocks at offset 0x00FFC000
Reading Block ID 0x008C at offset 0x00241800
Copying Block ID 0x008C at offset 0x0107BE00
Zeroing Block ID 0x008C at offset 0x00241800
== Remapped successfully ===========================

Do i just inject my rawconfig and rawkv and flash xbr?

#7 Martinchris23

Martinchris23

    X-S Messiah

  • Members
  • PipPipPipPipPipPipPip
  • 3,900 posts
  • Location:Scotland, UK
  • Xbox Version:v1.6
  • 360 version:v4.0 (jasper)

Posted 24 March 2010 - 08:50 PM

Just to note - error 250 is an empty block (or all zeroes) - it's possible to have a block of zeroes but NANDPro reads this as an error.

I had an error 250 recently with no remapping with my USB SPI Flasher. Just ignore it - it's not being remapped so the 360 won't go looking for it. As long as it's not at address 0x1 or 0x3de you'll be fine.

Remap the 0x8C and that should be all you need.

#8 TK-101

TK-101

    X-S Senior Member

  • Members
  • PipPip
  • 207 posts
  • Xbox Version:unk
  • 360 version:v3.0 (falcon)

Posted 24 March 2010 - 09:03 PM

Thanks for the help guys rolleyes.gif

1 more thing. Dont flame at me for this but a few people have asked me about ways to delay your ban on xbl with a jtag. I've never heard of this but i dont go online with my jtag so i havnt really looked up about it.

Also, he asked if theres a way to stop you from being auto flagged on xbl? uhh.gif

He cant make an account on here so i thought i'd do him a favor.




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users