Jump to content


Photo

Tsop Flash Help


  • Please log in to reply
5 replies to this topic

#1 f34rther34pr

f34rther34pr

    X-S Member

  • Members
  • Pip
  • 71 posts
  • Interests:modding, hacking
  • Xbox Version:v1.4
  • 360 version:v5.0 (360S - trinity)

Posted 16 May 2010 - 11:51 PM

i dont really know where to put this, so im just gonna take a guess and put it here. anyway, i've tried to flash my bios using this guide. it says flash not writable yet iv soldered this right points and everything. anybody have any suggestions

Edited by f34rther34pr, 16 May 2010 - 11:53 PM.


#2 Heimdall

Heimdall

    X-S Legend

  • Members
  • PipPipPipPipPipPipPipPipPip
  • 5,749 posts
  • Location:UK
  • Xbox Version:v1.4
  • 360 version:v4.0 (jasper)

Posted 17 May 2010 - 12:04 AM

Are you getting a message similar to:
"Manufacturer's ID 09 Device ID 00"

If so, what is it?

#3 f34rther34pr

f34rther34pr

    X-S Member

  • Members
  • Pip
  • 71 posts
  • Interests:modding, hacking
  • Xbox Version:v1.4
  • 360 version:v5.0 (360S - trinity)

Posted 17 May 2010 - 12:55 AM

QUOTE(Heimdall @ May 16 2010, 06:04 PM) View Post

Are you getting a message similar to:
"Manufacturer's ID 09 Device ID 00"

If so, what is it?

yes thats exactly what im getting. any idea why?

Edited by f34rther34pr, 17 May 2010 - 12:57 AM.


#4 Heimdall

Heimdall

    X-S Legend

  • Members
  • PipPipPipPipPipPipPipPipPip
  • 5,749 posts
  • Location:UK
  • Xbox Version:v1.4
  • 360 version:v4.0 (jasper)

Posted 17 May 2010 - 12:59 AM

That means it's your soldering. Double check that you're soldering the right points for your motherboard, clean the TSOP points, scrape them VERY gently with a craft knife to get rid of any surface oxidisation, and use lots of flux.

#5 f34rther34pr

f34rther34pr

    X-S Member

  • Members
  • Pip
  • 71 posts
  • Interests:modding, hacking
  • Xbox Version:v1.4
  • 360 version:v5.0 (360S - trinity)

Posted 17 May 2010 - 01:22 AM

so remove the solder from the points and resloder them

#6 xboxmods2977

xboxmods2977

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,156 posts
  • Xbox Version:v1.0
  • 360 version:none

Posted 07 June 2010 - 05:28 PM

Yes. Also, if you have a multimeter, you can check your soldering joints with it. Take a close look at those joints. All 4 points (the two pairs you joined with solder blobs) have traces which lead to either pads or other components nearby allowing you to confirm continuity between your newly bridged points.

Edited by xboxmods2977, 07 June 2010 - 05:30 PM.





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users