Jump to content


Photo

Blackcat Usb Jtag Tool?


  • Please log in to reply
17 replies to this topic

#1 xflasher101

xflasher101

    X-S Enthusiast

  • Members
  • 2 posts

Posted 12 January 2011 - 03:58 AM

Hey guys,

I purchased a Black Cat usb and was wondering if I could use it as a xbox 360 jtag tool. I got a few hits with the almighty goggle but nothing concrete. What I really want is a diagram of some sort. Thanks for sharing guys. smile.gif

#2 blackopsftw

blackopsftw

    X-S Member

  • Members
  • Pip
  • 78 posts

Posted 23 October 2011 - 08:04 PM

Same question as above!

#3 tomsawyer2k5

tomsawyer2k5

    X-S Member

  • Members
  • Pip
  • 73 posts
  • Xbox Version:unk
  • 360 version:v4.0 (jasper)

Posted 29 October 2011 - 08:18 AM

The thing is that it can work because the specs look good, but I don't know if nandpro supports it. So this is the problem. You can use the BlackCatUSB utility to get a dump, but will the output file be acceptable for use by FreeBoot programs, I don't know. The only way to find out is to experiment yourself. As long as you wire the flasher to the 360 accordingly and the voltage setting on the programmer itself is correct, then you won't damage your 360. BUT DO THIS AT YOUR OWN RISK!!! It can work, but it requires more "adapting" on your end. If you're willing to do this, then go ahead.

Edited by tomsawyer2k5, 29 October 2011 - 08:26 AM.


#4 koevoet

koevoet

    X-S Enthusiast

  • Members
  • 5 posts

Posted 05 November 2011 - 11:37 AM

The BlackcatUSB is actually now capable of reading/writing to the nands with the new beta software , still in Beta so speeds are not optimized and has so far only been tested on 16MB Nands .
http://imageshack.us...2011151018.png/
The image shows the software connected to the nand with the flash config.

Latest software is available at
CODE
http://www.embeddedcomputers.net/products/BlackcatUSB/


for the people that wish to test it out.

#5 kornwood

kornwood

    X-S Enthusiast

  • Members
  • 7 posts

Posted 10 November 2011 - 09:24 AM

sweet now what would the wiring diagram be
i cant find any info

#6 koevoet

koevoet

    X-S Enthusiast

  • Members
  • 5 posts

Posted 10 November 2011 - 05:37 PM

This is the layout for the BCUSB to NAND-SPI.

http://imageshack.us.../bcusbnand.jpg/

#7 kornwood

kornwood

    X-S Enthusiast

  • Members
  • 7 posts

Posted 11 November 2011 - 04:05 AM

oh sweet thank you koevoet

#8 foldor

foldor

    X-S Young Member

  • Members
  • Pip
  • 41 posts

Posted 15 November 2011 - 01:41 AM

QUOTE(koevoet @ Nov 10 2011, 12:37 PM)  

This is the layout for the BCUSB to NAND-SPI.

http://imageshack.us.../bcusbnand.jpg/


Thank you so much for this koevoet. I just want to clarify things before I go and wire up my console.
  1. I don't need any resistors or diodes do I?
  2. Should it be in 3.3v or 5v mode?
  3. You marked ground on the diagram, but didn't specify where to put it.
  4. Is Blackcat USB version 1.7 ok?

Thanks again.

#9 Technitian3

Technitian3

    X-S X-perience

  • Members
  • PipPip
  • 333 posts
  • Location:Mission, B.C.
  • Interests:alchemy, metallurgy, philosophy
  • Xbox Version:v1.6
  • 360 version:v3.0 (falcon)

Posted 15 November 2011 - 08:51 AM

QUOTE(foldor @ Nov 14 2011, 04:41 PM)  

Thank you so much for this koevoet. I just want to clarify things before I go and wire up my console.
  1. I don't need any resistors or diodes do I?
  2. Should it be in 3.3v or 5v mode?
  3. You marked ground on the diagram, but didn't specify where to put it.
  4. Is Blackcat USB version 1.7 ok?
Thanks again.

1- no
2- 3.3v
3- look harder at the diagram, specifically the pin numbering
4- if this is refering to a hardware revision it shouldn't matter

#10 foldor

foldor

    X-S Young Member

  • Members
  • Pip
  • 41 posts

Posted 15 November 2011 - 06:57 PM

QUOTE(Technitian3 @ Nov 15 2011, 03:51 AM)  

1- no
2- 3.3v
3- look harder at the diagram, specifically the pin numbering
4- if this is refering to a hardware revision it shouldn't matter


Ok you're right. Sorry, I looked at the diagram but got confused by the colors over the numbers. Ground is indeed on there. Everything else looks good, so I should be testing this tonight then biggrin.gif

#11 foldor

foldor

    X-S Young Member

  • Members
  • Pip
  • 41 posts

Posted 16 November 2011 - 02:40 AM

Ok, it looks like it worked! I was able tin install the Blackcat USB version 1.7 and use the software to dump my NAND just fine. One thing I think I should mention to people is to remember to plug in your console when attempting to dump the NAND. I had forgotten that step and it took me a while to realize what went wrong.

#12 mbg19

mbg19

    X-S Enthusiast

  • Members
  • 1 posts

Posted 30 November 2011 - 11:58 PM

I got it to work with the 1.7 version. Successfully dumped the firmware thanks for the diagram but im kind of new to this and im confused as i see that you have to write the firmware using other points. Has anyone managed to write to the NAND?

Edited by mbg19, 30 November 2011 - 11:58 PM.


#13 koevoet

koevoet

    X-S Enthusiast

  • Members
  • 5 posts

Posted 01 December 2011 - 08:13 PM

You use the same points to read/write to the nand , just on some models the size that you write back will differ.

#14 kornwood

kornwood

    X-S Enthusiast

  • Members
  • 7 posts

Posted 02 December 2011 - 02:17 AM

can i also use the blackcat for the matrix glitcher

#15 koevoet

koevoet

    X-S Enthusiast

  • Members
  • 5 posts

Posted 02 December 2011 - 03:30 PM

No the BCUSB can not program the CPLD as of yet.




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users