Jump to content


Photo

Errors While Flashing


  • Please log in to reply
11 replies to this topic

#1 Labomba

Labomba

    X-S Enthusiast

  • Members
  • 17 posts

Posted 31 January 2011 - 07:39 PM

Hi Folks,

I'm having problems flashing A 16D2S - 93450 drive, after flashing the drive dosflash displays: 256388 errors.
The drive is not flashed (erased) and nothing can be done with it.
I have a Xecuter switch that is installed and the switch it turned to R/W mode...the drive itselfs is visible and in vendor 0x72 mode....
I tried allot of other things, changing dosflash versions 1.8 - 1.7.
Even when flashing the original firmware I get the same errors, the card used is a VT6421A...

Can somebody help me out?


#2 Takashi

Takashi

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,744 posts
  • Xbox Version:v1.0
  • 360 version:v1 (xenon)

Posted 31 January 2011 - 09:34 PM

Dump the switch, they're junk.
Did you already get the key completely?

#3 Labomba

Labomba

    X-S Enthusiast

  • Members
  • 17 posts

Posted 31 January 2011 - 09:45 PM

QUOTE(Takashi @ Jan 31 2011, 09:34 PM) View Post

Dump the switch, they're junk.
Did you already get the key completely?


I have the stock firmware and this one contains the drive key.
It was flashed with a LT 1.1, now i wanted to update it to LT+ but i am unable to flash it...not with doshflash or jungleflasher...


#4 Labomba

Labomba

    X-S Enthusiast

  • Members
  • 17 posts

Posted 01 February 2011 - 06:00 PM

Anyone please ?

QUOTE(Labomba @ Jan 31 2011, 09:45 PM) View Post

I have the stock firmware and this one contains the drive key.
It was flashed with a LT 1.1, now i wanted to update it to LT+ but i am unable to flash it...not with doshflash or jungleflasher...



#5 Labomba

Labomba

    X-S Enthusiast

  • Members
  • 17 posts

Posted 06 February 2011 - 06:52 PM

Could it be possible that i am using the wrong dvd key?
Writing the flash works, but after wards i get errors:

- jungleflasher: Write verify failed
- dosflash: 256336 errors

#6 iateshaggy

iateshaggy

    X-S Hacker

  • Members
  • PipPipPipPipPipPip
  • 2,514 posts
  • Xbox Version:v1.6
  • 360 version:v4.0 (jasper)

Posted 06 February 2011 - 07:17 PM

step one, remove the lt switch. until you do that, there is no magic words we can tell you that will make the drive work. be very careful, usually when people remove these things, they rip every trace up with them, then you will have to buy a new pcb which might be the easiest thing anyway.

#7 Labomba

Labomba

    X-S Enthusiast

  • Members
  • 17 posts

Posted 06 February 2011 - 08:18 PM

QUOTE(iateshaggy @ Feb 6 2011, 07:17 PM) View Post

step one, remove the lt switch. until you do that, there is no magic words we can tell you that will make the drive work. be very careful, usually when people remove these things, they rip every trace up with them, then you will have to buy a new pcb which might be the easiest thing anyway.


Thnx for the answer, i will remove the switch ASAP.
And when the switch is removed what should i do afterwards?

#8 Labomba

Labomba

    X-S Enthusiast

  • Members
  • 17 posts

Posted 06 February 2011 - 08:48 PM

removed the switch with a desolder pump, pcb is fine, except for the trace cuts that where needed for the switch.
Drive now is not recognized because it was erased...unable to open the tray, and nothing detects by drive.

#9 Takashi

Takashi

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,744 posts
  • Xbox Version:v1.0
  • 360 version:v1 (xenon)

Posted 06 February 2011 - 09:40 PM

take a cpl macro pics of the board also

#10 Labomba

Labomba

    X-S Enthusiast

  • Members
  • 17 posts

Posted 08 February 2011 - 06:19 PM

QUOTE(Takashi @ Feb 6 2011, 09:40 PM) View Post

take a cpl macro pics of the board also


Just looks the same as this one......
IPB Image

#11 Takashi

Takashi

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,744 posts
  • Xbox Version:v1.0
  • 360 version:v1 (xenon)

Posted 09 February 2011 - 01:02 AM

failpic

We need to see YOUR work, not someone elses.

Edited by Takashi, 09 February 2011 - 01:03 AM.


#12 Labomba

Labomba

    X-S Enthusiast

  • Members
  • 17 posts

Posted 09 February 2011 - 06:54 PM

QUOTE(Takashi @ Feb 9 2011, 01:02 AM) View Post

failpic

We need to see YOUR work, not someone elses.


Nevermind, drive is f*cked up...need to buy another one.
Thnxx for the efforts




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users