Jump to content


Photo

Burning Cod Mw3 Using Ixtreme Burner Max


  • Please log in to reply
7 replies to this topic

#1 ckeays

ckeays

    X-S Enthusiast

  • Members
  • 19 posts

Posted 09 November 2011 - 06:16 PM

Hello Guys,

I have the iHAS124b with modded firmware, latest version of imgburn. I backed up my COD MW3 disc
I purchased yesterday using XBC and the 0800 drive with the V3 firmware.

Trying to write the image to a blank DL disc using imgburn (settings are correct)
and an iHAS1124b (modded ALOS firmware).

I still get the error message that the image is too large to fit the disc.

I cancelled the write.

Should I be seeing the message?

Will the modded iHAS writer just write the whole image?

I don't want to write only part of the image, I want to be sure imgburn will do 100% of the image.

Any help would be appreciated!

Edited by ckeays, 09 November 2011 - 06:19 PM.


#2 tomgreen99200

tomgreen99200

    X-S Freak

  • Members
  • PipPipPipPipPip
  • 1,556 posts
  • Location:Florida
  • Xbox Version:v1.6
  • 360 version:v4.0 (jasper)

Posted 10 November 2011 - 12:13 AM

No you shouldn't be getting that error message if you truly have a iHAS1124b with LT MAX. Make sure you are using the latest version of Imgburn.

#3 IDONTuseKYJELLY

IDONTuseKYJELLY

    X-S Enthusiast

  • Members
  • 5 posts
  • Xbox Version:unk
  • 360 version:v4.0 (jasper)

Posted 10 November 2011 - 08:46 PM

Make sure you flashed your drive correctly with the IMAX Burner Firmware, and as he said above.

#4 Gokussj5okazu

Gokussj5okazu

    X-S Expert

  • Members
  • PipPipPip
  • 567 posts
  • Xbox Version:v1.1
  • 360 version:v2 (zephyr)

Posted 10 November 2011 - 08:52 PM

Just for shits and giggles, use Flash Util. to revert to your stock firmware, then crossflash it to a iHAS324, THEN flash with iXtreme. That should work perfectly, as I did mine that way.

#5 ep99

ep99

    X-S Member

  • Members
  • Pip
  • 62 posts
  • Location:Canada
  • Xbox Version:none
  • 360 version:unknown

Posted 12 November 2011 - 06:21 PM

I find that if you have the following entries in imgburn log...at least your hardware should have been setup correctly. Your XGD3 image should be ok and with the correct layer break.


I 16:50:28 Advanced Settings - Force HT: Yes, Online HT: Yes, OverSpeed: No, SmartBurn: Yes
I 16:50:28 Optimal L0 Data Zone Capacity: 2.133.520
I 16:50:28 Optimal L0 Data Zone Method: Copied From Original Disc
I 16:50:29 Set L0 Data Zone Capacity Succeeded!

#6 cheapjeep78

cheapjeep78

    X-S Enthusiast

  • Members
  • 1 posts

Posted 11 January 2012 - 06:31 AM

I have the same setup but get a full burn but always a unrecognized disc.
Ihas124b flashed with burner max
Benq 0800
Verbatim mkm 001 @ 2.4
Latest imgburn
Agbx verified
Hitachi 46 & 47 both give unrecognized disc
Running lt 3.0
All old backups work great but no xdg3.
Any help would be appreciated.
New to the forums so email if I don't respond often. Thanks


#7 bbcorvette2000

bbcorvette2000

    X-S Enthusiast

  • Members
  • 18 posts

Posted 12 January 2012 - 11:40 AM

QUOTE(cheapjeep78 @ Jan 10 2012, 11:31 PM)  

I have the same setup but get a full burn but always a unrecognized disc.
Ihas124b flashed with burner max
Benq 0800
Verbatim mkm 001 @ 2.4
Latest imgburn
Agbx verified
Hitachi 46 & 47 both give unrecognized disc
Running lt 3.0
All old backups work great but no xdg3.
Any help would be appreciated.
New to the forums so email if I don't respond often. Thanks


Have you tested your backups with kprobe or Nero speed? Even though the media is good, the burn quality could be bad. I used MKM001's as well and achieved the best results burning at 4x (score of 95 on NeroSpeed) with the following settings.

EEPROM: enable all except for OHT (disable) clear OPC (also make sure to power cycle drive to make changes effective)

IMGBURN: OPC off, burnproof off


#8 tim132

tim132

    X-S Enthusiast

  • XS-BANNED
  • 13 posts
  • Xbox Version:unk
  • 360 version:unknown

Posted 18 January 2012 - 04:10 PM

QUOTE(cheapjeep78 @ Jan 11 2012, 05:31 AM)  

I have the same setup but get a full burn but always a unrecognized disc.
Ihas124b flashed with burner max
Benq 0800
Verbatim mkm 001 @ 2.4
Latest imgburn
Agbx verified
Hitachi 46 & 47 both give unrecognized disc
Running lt 3.0
All old backups work great but no xdg3.
Any help would be appreciated.
New to the forums so email if I don't respond often. Thanks


I would say this is due to a weak laser, XGD3 backups are known to be harder to read than XGD2 and originals. You could try a pot tweak or install a new laser. I would go for the pot tweak first, solved my problems in the past!




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users