Jump to content


Photo

Did First Part Of Rgh, Jasper Wont Boot


  • Please log in to reply
5 replies to this topic

#1 BBCHAMPs

BBCHAMPs

    X-S Young Member

  • Members
  • Pip
  • 49 posts
  • Location:Sunrise, Fl
  • Xbox Version:unk
  • 360 version:v1 (xenon)

Posted 04 February 2012 - 02:43 AM

Hey guys i installed all the nand-x/jtag qsb's and followd jtag tool tutorial. got 3 copies of nand, all matching, and wrote xell to it with jtag tool. now i get rrod no display with 0022 as my secondary. hopefully i didnt mess anything up.

Help please!!

#2 BBCHAMPs

BBCHAMPs

    X-S Young Member

  • Members
  • Pip
  • 49 posts
  • Location:Sunrise, Fl
  • Xbox Version:unk
  • 360 version:v1 (xenon)

Posted 04 February 2012 - 04:16 AM

Ok so i restored my original nand and now the xbox boots back up perfect. I am re-reading the nand to see if i still match, then i'm not sure the step after that. I dont have the CoolRunner portion installed, i still have the Nand-x + QSB's that came with that kit. I can take a picture but the install is clean.

Any input would REALLY be helpful as im totally new to this

Edit this is what i get on the new read

IPB Image

Edited by BBCHAMPs, 04 February 2012 - 04:51 AM.


#3 ravendrow

ravendrow

    X-S Senior Member

  • Members
  • PipPip
  • 285 posts
  • Xbox Version:unk
  • 360 version:v5.0 (360S - trinity)

Posted 05 February 2012 - 12:06 AM

QUOTE(BBCHAMPs @ Feb 3 2012, 08:16 PM) View Post

Ok so i restored my original nand and now the xbox boots back up perfect. I am re-reading the nand to see if i still match, then i'm not sure the step after that. I dont have the CoolRunner portion installed, i still have the Nand-x + QSB's that came with that kit. I can take a picture but the install is clean.

Any input would REALLY be helpful as im totally new to this

Edit this is what i get on the new read

IPB Image

bad connection most likely the ground cut the yellow wire where it connects to the nand-x Qsb and connect it to the case of the 360 or the metal on one of the memory unit ports

Edited by ravendrow, 05 February 2012 - 12:07 AM.


#4 BBCHAMPs

BBCHAMPs

    X-S Young Member

  • Members
  • Pip
  • 49 posts
  • Location:Sunrise, Fl
  • Xbox Version:unk
  • 360 version:v1 (xenon)

Posted 05 February 2012 - 03:17 AM

QUOTE(ravendrow @ Feb 4 2012, 05:06 PM) View Post

bad connection most likely the ground cut the yellow wire where it connects to the nand-x Qsb and connect it to the case of the 360 or the metal on one of the memory unit ports


Then what? Redump? Thanks for your help

#5 ravendrow

ravendrow

    X-S Senior Member

  • Members
  • PipPip
  • 285 posts
  • Xbox Version:unk
  • 360 version:v5.0 (360S - trinity)

Posted 05 February 2012 - 05:25 PM

QUOTE(BBCHAMPs @ Feb 4 2012, 07:17 PM) View Post

Then what? Redump? Thanks for your help

re write your dump and pray it was a good one

#6 noraa

noraa

    X-S Young Member

  • Members
  • Pip
  • 48 posts

Posted 06 February 2012 - 08:34 PM

no need to write or dump so far, from your config, you have a 256 Jasper, only need FFF or 64megs, not a full 256. Save you some time reading and writing.

Also if you flashed in your orig nand and it boots, no need to re dump as its obviously a good image. Most
likely your ecc is bad or bad write. Use multibuilder .07 to create ecc and make sure you write the image
in as +w NOT -w.

nandpro usb: +w64 jasper.ecc

Edited by noraa, 06 February 2012 - 08:36 PM.





0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users