Jump to content


Photo

Liteon


  • Please log in to reply
8 replies to this topic

#1 bigshow1up

bigshow1up

    X-S Member

  • Members
  • Pip
  • 78 posts

Posted 01 October 2012 - 06:33 AM

Ok so I have a liteon drive, the dvd drive would not open, it tried but was stuck. I took drive out of the case cleaned everything. now im getting the green blinking light and the drive will not respond . I hooked up another drive to the motherboard and it worked just fine.


What can I do to fix this, thanks ahead of time.

#2 wilgo45

wilgo45

    X-S Expert

  • Members
  • PipPipPip
  • 701 posts

Posted 01 October 2012 - 08:52 AM

The green light is blinking because the drive is trying to open. The center light blinks when the drive tray opens. Even when everything is working.

The belt inside, that turns the gears, is slipping. Or stretched out of shape.

Either re-condition the belt or replace.

#3 iateshaggy

iateshaggy

    X-S Hacker

  • Members
  • PipPipPipPipPipPip
  • 2,514 posts
  • Xbox Version:v1.6
  • 360 version:v4.0 (jasper)

Posted 01 October 2012 - 11:49 AM

either that or he's not telling you that he erased the drive.

#4 bigshow1up

bigshow1up

    X-S Member

  • Members
  • Pip
  • 78 posts

Posted 01 October 2012 - 04:16 PM

Good point ....the drive is 100% stock nothing has been done to it.

#5 bigshow1up

bigshow1up

    X-S Member

  • Members
  • Pip
  • 78 posts

Posted 01 October 2012 - 05:35 PM

Well I just swapped the pcb into a new working drive and still nothing.....the green light flashes sometimes and stays solid other times.... but the drive is still unresponsive. Im lost as to what is going on

#6 BoNg420

BoNg420

    X-S Messiah

  • Head Moderator
  • PipPipPipPipPipPipPip
  • 3,803 posts
  • Location:USA
  • Xbox Version:none
  • 360 version:v5.0 (360S - trinity)

Posted 01 October 2012 - 06:38 PM

maybe damage to the connectors or the wires bad or loose in the connector

#7 bigshow1up

bigshow1up

    X-S Member

  • Members
  • Pip
  • 78 posts

Posted 01 October 2012 - 07:43 PM

I replaced all wires with new same problem...I tried the drive out before I swapped the pcb on the motherboard and everything was working fine...I then swapped the pcb and now it will not respond..when i push eject the light blinks but nothing happens when i push it again the light stops blinking but nothing happens in the drive.

#8 wilgo45

wilgo45

    X-S Expert

  • Members
  • PipPipPip
  • 701 posts

Posted 02 October 2012 - 03:11 AM

Maybe its the 3.3 v regulator for the dvd drive.

That device is on the main board. Near the port connector for the hard drive.

Or it could be the power reg IC on the logic board of the dvd drive.

You should check the voltages on the power cable. You should have One - 3.3 .... one - 5 v and two 12 volt lines

#9 iateshaggy

iateshaggy

    X-S Hacker

  • Members
  • PipPipPipPipPipPip
  • 2,514 posts
  • Xbox Version:v1.6
  • 360 version:v4.0 (jasper)

Posted 02 October 2012 - 03:14 AM

so u try one pcb and it works, and the other u get a blinking light and no response. you erased the drive. u got the dvd key first?




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users