Jump to content


Photo

Fs: Jtagged Xenon 360 W/out Drive - Rrod


  • Please log in to reply
10 replies to this topic

#1 Jroz

Jroz

    X-S Enthusiast

  • Members
  • 4 posts

Posted 02 October 2012 - 02:15 PM

Hi Guys,

I bought a Jtagged Xenon Xbox 360 w/out Drive from a member here about a year 1/2 ago and it worked great...while it lasted...but anyways i'm looking to sell the system now. Booted it up a few days ago and it RROD. Comes with component cables, 20gig MS hard drive. Boots directly into FSD, let me know if you have any questions. I'm not sure what one of these goes for, so taking best offers, msg me if interested, here is a vid I took of it a few weeks ago in action (note fan is set to 80% in video).



I also have two great working h@cked xbox 360 controllers that each come with their own harness...perfect for using in an arcade cabinet or building your own control panels. I paid $140 for these controllers (40 a hack, 30 a controller) I'd like 100 shipped

thanks
Jason

#2 kip3000

kip3000

    X-S Enthusiast

  • Members
  • 22 posts
  • Location:S W Michigan USA
  • Interests:Game console repair. All kinds.
  • Xbox Version:v1.4
  • 360 version:v4.0 (jasper)

Posted 03 October 2012 - 12:20 PM

What's the Secondary Error Code?
Thanks

#3 Jroz

Jroz

    X-S Enthusiast

  • Members
  • 4 posts

Posted 03 October 2012 - 05:07 PM

hmm..sorry to be a newb but how can I tell? It has the 3 red rings

#4 kip3000

kip3000

    X-S Enthusiast

  • Members
  • 22 posts
  • Location:S W Michigan USA
  • Interests:Game console repair. All kinds.
  • Xbox Version:v1.4
  • 360 version:v4.0 (jasper)

Posted 03 October 2012 - 05:13 PM

How to get the E-code

The E-code only shows up if you get 1 red light, otherwise there is no video output and you cant see it(for 2, 3 and 4 red lights)...(in rare cases it doesnt even show up if you get 1 red light, proceed with the secondary error code then)

An E-code consist out of 3 letters, it always starts with an E that is followed by two numbers, for example your error code would be E74 in the picture below!



How to get the Secondary error code

The specific type of hardware failure can be determined by a \"hidden\" error code

* Turn the xbox 360 on, and wait till the 3 red lights are flashing.
* Press and hold the sync up button (the small white one), while holding that button press the eject button.
* The LEDs will now blink the first number in the code (as described below).
* Release the eject button and press it again.
* The LEDs will now blink the second number of the code.
* Release the eject button and press it again.
* The LEDs will now blink the third number of the code.
* Release the eject button and press it again.
* The LEDs will now blink the forth number of the code.
* Release the eject button and press it again.
* The LEDs will go back to the 3 red flashing lights.
You should be able to determine the difference between the 3 flashing lights and the error code lights by the rate in which they flash.

Here is how you interpret the LEDs to get the code number:

* All four lights flashing - 0
* One light flashing - 1
* Two Lights flashing - 2
* Three lights flashing - 3


You will for example get an error code like 0102 if you get 4 lights after the first click, 1 after the second, 4 after the third and 2 after the fourth click of the eject button...

All credits for this go to Xbox-scene.com


#5 Jroz

Jroz

    X-S Enthusiast

  • Members
  • 4 posts

Posted 03 October 2012 - 05:18 PM

I believe its this one..

Sections 1, 3, and 4 are flashing red
- General Hardware Failure
/ \
\ /

Check the secondary Error Code per the instructions in the section below

THINGS TO TRY
1.Try restarting the console.
2.If restarting the console does not resolve the behavior, follow these steps:
◦Turn the console off.
◦Unplug all the power and AV cables from the console.
◦Unplug the power cord from the wall socket.
◦Firmly reconnect all the cables.
◦Turn on the console.
3.If these steps do not resolve the behavior, turn the console off, remove the hard drive, and then turn on the console. If the 3x Red LED error light is no longer displayed, turn the console off, re-attach the hard drive, and then turn on the console.
4.Also examine the lights on the power supply. When you turn on the console, the power supply light should illuminate green even if the three lights on the RoL flash red.


#6 Jroz

Jroz

    X-S Enthusiast

  • Members
  • 4 posts

Posted 03 October 2012 - 05:39 PM

I'll follow up tonight when I get home from work..thanks

#7 Jroz

Jroz

    X-S Enthusiast

  • Members
  • 4 posts

Posted 07 October 2012 - 04:08 PM

So sorry for the delayed response on this...I'm getting code 0102 . Let me know if interested..thanks!

#8 Jroz

Jroz

    X-S Enthusiast

  • Members
  • 4 posts

Posted 08 October 2012 - 05:25 PM

Bump, entertaining all offers.

#9 Jroz

Jroz

    X-S Enthusiast

  • Members
  • 4 posts

Posted 09 October 2012 - 08:20 PM

No interest at all on this thing?.....

#10 Jroz

Jroz

    X-S Enthusiast

  • Members
  • 4 posts

Posted 12 October 2012 - 02:24 PM

bump, take me, fix me

#11 Jroz

Jroz

    X-S Enthusiast

  • Members
  • 4 posts

Posted 15 October 2012 - 04:39 PM

Think its worth getting the RROD fixed and selling it afterwards?...really dont have any more use for this thing.




0 user(s) are reading this topic

0 members, 0 guests, 0 anonymous users