xbox-scene.com - your xbox news information source
Quick Links: Main Forums | Xbox360 Forums | Xbox1 Forums | PS3 Forums
Xbox-Scene Forum Help  Search Xbox-Scene Forums   Xbox-Scene Forum Members   Xbox-Scene Calendar

Giganews Usenet Offers: +1150 days binary retention, 99%+ Completion, and Unlimited Speed/Access!

360 ODD Emulators: X360 Key $99 | Wasabi360 FAT $99 | Wasabi360 Slim $99
C4E's iXtreme Burner MAX Drive: LiteOn iHAS124 DROPPED TO JUST $17


Welcome Guest ( Log In | Register )

 Forum Rules Rules
 
 Reply to this topicStart new topic
> This Falcon Board Is Being A Pain, RGH Install
SergioFoX
post Feb 13 2012, 05:31 PM
Post #1


X-S Member
*

Group: Members
Posts: 90
Joined: 10-March 04
Member No.: 106153
I got my coolrunner chip all wired up and the console will not boot (black screen, 3 RROD after a while) with the wire going to the cpu bypass, even if that wire is not connected to the chip. I tried a new wire and the same thing, checked for any solder was touching the surrounding area, at first it was and I cleaned and redid it. I remove the wire and boots up fine, both chip on or off.

Should I remove the cpu heatsink and try using the other cpu pll bypass point or have I caused some damage when I bridged that point to the resister right above it?

IPB Image

IPB Image
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SergioFoX
post Feb 14 2012, 10:10 PM
Post #2


X-S Member
*

Group: Members
Posts: 90
Joined: 10-March 04
Member No.: 106153
no one?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cRaCKwHoRe
post Feb 14 2012, 10:53 PM
Post #3


X-S Senior Member
**

Group: Members
Posts: 271
Joined: 16-December 02
Member No.: 13557
Xbox Version: unk
360 version: v5.0 (360S - trinity)
All I can say is 9 out of 10 issues are soldering-related... I would check each and every point with a magnifying glass and make for damn sure nothing is out of the ordinary...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SergioFoX
post Feb 14 2012, 11:26 PM
Post #4


X-S Member
*

Group: Members
Posts: 90
Joined: 10-March 04
Member No.: 106153
Thanks for your reply.

I removed all the wires and chip and it works fine, with a wire going to that cpu pll there is no boot.
Nothing is touching so I don't know, tested with a voltmeter.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
cRaCKwHoRe
post Feb 15 2012, 02:23 PM
Post #5


X-S Senior Member
**

Group: Members
Posts: 271
Joined: 16-December 02
Member No.: 13557
Xbox Version: unk
360 version: v5.0 (360S - trinity)
You did flash the chip right? Also, when you turn it on with it all wired up, does the LED on the chip turn on? Do you hear the Xbox spin up and down? Do the LED's on the chip turn from red to green, and then back to red at all?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Dicko316
post Feb 16 2012, 01:34 AM
Post #6


X-S Senior Member
**

Group: Members
Posts: 214
Joined: 1-March 10
Member No.: 433831
Xbox Version: none
360 version: v5.0 (360S - trinity)
sounds like he hasnt even read the nand and flashed the .ecc file.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SergioFoX
post Feb 24 2012, 12:06 AM
Post #7


X-S Member
*

Group: Members
Posts: 90
Joined: 10-March 04
Member No.: 106153
QUOTE(Dicko316 @ Feb 16 2012, 01:34 AM) *

sounds like he hasnt even read the nand and flashed the .ecc file.


Correct, I did not read or flash the nand but I did flash the chip.
The biggest issue is that if anything is soldered to that point the xbox will not boot.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
deilzfcjk
post Feb 24 2012, 12:51 AM
Post #8


X-S Genius
****

Group: Members
Posts: 802
Joined: 23-June 06
From: San Francisco
Member No.: 287206
Xbox Version: v1.6
360 version: v4.0 (jasper)
Man do you know that rgh will not boot a stock dashboard.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
SergioFoX
post Feb 24 2012, 01:37 AM
Post #9


X-S Member
*

Group: Members
Posts: 90
Joined: 10-March 04
Member No.: 106153
QUOTE(deilzfcjk @ Feb 24 2012, 12:51 AM) *

Man do you know that rgh will not boot a stock dashboard.


I believe I have never had an issue booting stock with the chip on..
But the problem here and I'm not sure if anyone knows I just have a wire going to that point not touching anything or connecting back to the chip and the console will not boot until that wire is removed.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post




 

Reply to this topicStart new topic

 

Lo-Fi Version Time is now: 23rd May 2013 - 10:04 AM
Invision Power Board v2.1.7 © 2013  IPS, Inc.
Licensed to: Scenyx