 Quick Links: Main Forums | Xbox360 Forums | Xbox1 Forums | PS3 Forums |
|
|
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
  |
 X2.3 Lite + Problems, need a lotta help, plz help |
| xbox11334 |
 Dec 18 2003, 10:04 PM
Post
#1
|
 X-S X-perience  Group: XS-BANNED Posts: 410 Joined: 8-July 03 Member No.: 48369 Xbox Version: unk  |
i just bought an x2.3 lite +, and i installed it, and got the usb power adaptersupplied so all the lights were on, or so until i turned the modchip on, the minute i turn the modchip on, the green light goes off, and the xbox frags...ppl said it was my lpc ports that they were dirty but i doubt it, cuz why would that make the green light go off....any suggestions at all???
|
   |
 
|
| xbox11334 |
Dec 18 2003, 10:10 PM
Post
#2
|
|
X-S X-perience Group: XS-BANNED Posts: 410 Joined: 8-July 03 Member No.: 48369 Xbox Version: unk |
could it be the bios??? i know a bad bios makes it frag, but i didn't flash the bios yet, i got it from smt, and the greeen light on the chip goes off, would the green d0 light on the chip go off if it's a bad bios
|
|
|
|
| sparkac |
Dec 18 2003, 10:21 PM
Post
#3
|
|
X-S X-perience Group: Members Posts: 393 Joined: 10-April 03 Member No.: 31401 |
frags are usually caused by the lpc ports, clean them
also check if your modchip is aligned |
|
|
|
| lan122 |
Dec 18 2003, 11:51 PM
Post
#4
|
|
X-S Expert Group: Members Posts: 566 Joined: 26-October 03 Member No.: 70227 Xbox Version: v1.4 360 version: v1 (xenon) |
Never used a 2.3 lite +, but on a 2.2 lite + the green light on the chip is supposed to go off when the chip is enabled.
As far a the frags, those suckers can be pretty hard to get llined up. Also I have heard that it is important to make sure you have a good ground with those 2.3's. Check the tut on installing there's a section on grounding the chip. |
|
|
|
| xbox11334 |
Dec 19 2003, 07:34 PM
Post
#5
|
|
X-S X-perience Group: XS-BANNED Posts: 410 Joined: 8-July 03 Member No.: 48369 Xbox Version: unk |
how do i clean the lpc ports, and i think it is aligned, cuz the green light shows that the d0 is, and i checked the lpcs, is there a way to clean the lpc ports without killing them like with a razor, cna i just cleant hem with my hands, cuz i already tried that
|
|
|
|
| xbox11334 |
Dec 19 2003, 07:35 PM
Post
#6
|
|
X-S X-perience Group: XS-BANNED Posts: 410 Joined: 8-July 03 Member No.: 48369 Xbox Version: unk |
could the frags be becuzof a bad bios it came with, i have a programmer?
and where can i find tuts on 2.3s, i've chexcked system-mods.com, and i've looked at all of theirs This post has been edited by xbox11334: Dec 19 2003, 07:35 PM |
|
|
|
| DexX |
Dec 19 2003, 07:49 PM
Post
#7
|
 X-S Senior Member Group: Members Posts: 167 Joined: 15-November 03 Member No.: 74352 |
well how did you install your chip with what tutorials?
|
|
|
|
| BobDobbs |
Dec 19 2003, 08:09 PM
Post
#8
|
|
X-S Enthusiast Group: Members Posts: 11 Joined: 12-September 03 Member No.: 62121 |
Well, I've installed 3 X2.3+ chips this week... I had some problems with one of them... they sent me a bad USB board. Couldn't get BLUE lights on. (Had to splice and solder power straight to Controller port wires to avod waiting
 ) If it reboots 3 times then FRAGs you need to get your D0 aligned. (green light may still come on, tho). I had to also use my dremel to elongate the screw hole (TOWARDS THE CHIP) to get one installed. I could plainly see that the D0 spiked pin was too far FORWARD. This completely fixed the problem! This was a version 1.1 . Also may sure of the obvious... is your switch set for the correct version? BobDobbs |
|
|
|
| xbox11334 |
Dec 19 2003, 08:50 PM
Post
#9
|
|
X-S X-perience Group: XS-BANNED Posts: 410 Joined: 8-July 03 Member No.: 48369 Xbox Version: unk |
i tested my version, and from what i tested i'm a version 1.0, but maybe they're wrong, if i switch the switch will i screw up my xbox if it's wrong?
|
|
|
|
|
| Lo-Fi Version | Time is now: 22nd May 2013 - 08:28 AM |
