xbox-scene.com - your xbox news information source
Quick Links: Main Forums | Xbox360 Forums | Xbox1 Forums | PS3 Forums
Xbox-Scene Forum Help  Search Xbox-Scene Forums   Xbox-Scene Forum Members   Xbox-Scene Calendar

Giganews Usenet Offers: +1150 days binary retention, 99%+ Completion, and Unlimited Speed/Access!

360 ODD Emulators: X360 Key $99 | Wasabi360 FAT $99 | Wasabi360 Slim $99
C4E's iXtreme Burner MAX Drive: LiteOn iHAS124 DROPPED TO JUST $17


Welcome Guest ( Log In | Register )

 Forum Rules Rules
 
 Reply to this topicStart new topic
> 2.6 Installed Correctly But.....
Khaavren
post Sep 26 2004, 11:52 PM
Post #1


X-S Enthusiast


Group: Members
Posts: 20
Joined: 8-January 03
Member No.: 17413
When it boots, i get the normal xbox dashboard, with and without the chip turned on. Could i perhaps not have the external adapter connected comepletely? It is a v1.1 xbox, used pin headers connected d0 and hdd lan leds.

This post has been edited by Khaavren: Sep 26 2004, 11:57 PM
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Cold Fuzion
post Sep 27 2004, 01:27 AM
Post #2


X-S Senior Member
**

Group: Members
Posts: 299
Joined: 25-September 04
From: Georgia
Member No.: 150291
Xbox Version: v1.1
select bank 1 on the switch and should boot into crumwell

This post has been edited by Cold Fuzion: Sep 27 2004, 01:30 AM
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Khaavren
post Sep 27 2004, 04:09 AM
Post #3


X-S Enthusiast


Group: Members
Posts: 20
Joined: 8-January 03
Member No.: 17413
tried both bank 1 and bank 2, both boot to ms dashboard
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Jfave
post Sep 27 2004, 04:54 AM
Post #4


X-S Enthusiast


Group: Members
Posts: 15
Joined: 11-February 04
From: Port Hueneme, Ventura County, Ca
Member No.: 99260
Xbox Version: v1.4
have you rechecked your solder points?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
acemilo
post Sep 27 2004, 06:45 AM
Post #5


X-S Messiah
*******

Group: Members
Posts: 3828
Joined: 10-June 03
Member No.: 43103
Xbox Version: v1.0
360 version: unknown
You should not have the adapter plugged into the chip while its installed on the xbox. Also, if you flashed the bios using the programmer, then it probably installed fine. You must change the dashboard yourself.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
mR 54
post Sep 27 2004, 08:38 AM
Post #6


X-S Senior Member
**

Group: Members
Posts: 193
Joined: 7-September 04
Member No.: 145153
Check below the green X when you start up your box it should have soming like "XECUTER 2" but will still load the MS dash until you install your own. then I think you know its flashed OK.

blink.gif
User is offlineProfile CardPM
Go to the top of the page
+Quote Post




 

Reply to this topicStart new topic

 

Lo-Fi Version Time is now: 22nd May 2013 - 11:34 PM
Invision Power Board v2.1.7 © 2013  IPS, Inc.
Licensed to: Scenyx