Xecuter 3 Ce, I have some questions about my xecuter 3CE Options

[cobain339]

I have just ordered a modchip XecuterCE and A hdd 120gb seagate ST3120022A( i hope this is lockable) and i have a few questions

1. Can somebody please show a link that gives instructions on how to install an Xecuter 3 CE?
2. I want to have Evox as my dashboard so do i install evox before I install the modchip or after I install it? 2.5 If i install it after the mod chip do i install evox before or after i install the bios.
3. I understand what bios are but like are there sets up bios you get or do you choose which bios you get individually and how do you know which bios do what? Or do you just install the most current bios.
4. I have also purchased hdd (120gb) Can i attach the modchip and the HDD at the same time or will i have to attach the modchip configure evox, get bios, reopen xbox and attach hdd?

Answers to any of the questions is appreciated Thx.

[boob1966]

1/ http://www.team-xecuter.com/

2/ install x3 then bios then dash
best way to setup new dash is use AID3 installer

3/ x3 3294 bios is used with x3
x3 3294 for v1.0 to v1.5 xboxs
x3 3294 v16 plus for v1.6 v1.6b xboxs
once you flashed the bios you will have to set it up to boot to the dash your going to use
http://x3.bustedchain.com/index.html


4/you can install hard drive after you have installed the chip but you will have to format and rebuild the new hard drive then reinstall ms dash as well as hacked dash then setup x3 bios to use bigger hard drive

120G use F/ gets all

start reading guild in this site as well as team-xecuter for howtoo before you start

This post has been edited by boob1966: Sep 28 2006, 01:07 AM

[cobain339]

Thx a lot this is great

[cobain339]

Ok thnx for the great reply but im still a little fuzzy.

im just gonna go through the steps that i would take please correct me if im wrong

1.install modchip
2.flash bios onto modchip
3.Put in new dashboard(not 100%sure how)
4.reconfig xbox
5. install new HDD
6.customize settings
7.done

[boob1966]

install chip
flash bios
install new H/D
rebuild new H/D with ms dash as well as hacked dash(XBMC avalanuch evox)
customize settings in x3config
done

to rebuild hard drive use Auto installer deluxe 3 not aload to give site but goto www.team-xecuter.com in there forum find me under DJBOOBY in sig theres a site for it
dont use softmod option in AID3

This post has been edited by boob1966: Sep 28 2006, 04:08 AM

[cobain339]

So after i install the hd i should get my dashboard correct? Then rebuild Hd with the dashboard? or rebild using Auto installer deluxe 3? When i get Autoinstaller onto my computer where do i put it on my xbox? And when i turn on my xbox with auto installer in it where do i go to find it?

[boob1966]

AID3 is a image you burn to a dvd that you put into your xbox then reboot it then once AID3 come up with a screen with the a lot of option you need to format and setup new large hard drive then once thats done you need to install MS dash(it will install into C:/) then a h/dash like xbmc or avalanuch (pick E:/ install option) and use E:/ F:/ dash then install dvd2xbox (install in F:/) well as (put games onto your hard drive
once you done that reboot xbox then settup x3config to boot h/dash (name)as well as were it is (E:/) then reboot it shounld go to your h/dash with chip on and ms dash with chip off
done

This post has been edited by boob1966: Sep 30 2006, 11:59 PM