xbox-scene.com - your xbox news information source
Quick Links: Main Forums | Xbox360 Forums | Xbox1 Forums | PS3 Forums
Xbox-Scene Forum Help  Search Xbox-Scene Forums   Xbox-Scene Forum Members   Xbox-Scene Calendar

Giganews Usenet Offers: +1150 days binary retention, 99%+ Completion, and Unlimited Speed/Access!

360 ODD Emulators: X360 Key $99 | Wasabi360 FAT $99 | Wasabi360 Slim $99
C4E's iXtreme Burner MAX Drive: LiteOn iHAS124 DROPPED TO JUST $17


Welcome Guest ( Log In | Register )

 Forum Rules Rules
 
 Reply to this topicStart new topic
> Mosfet Replacement
gummyworm31
post Jun 3 2007, 08:02 PM
Post #1


X-S Young Member
*

Group: Members
Posts: 56
Joined: 21-May 07
Member No.: 343127
I did a lot of looking around on the forum, and i seem to have found a fix for 0002 errors. According to Got4M4xx, most 0002 errors are caused be bad mosfets (typically the 2 just down from the CPU and GPU) I ordered some samples from ON semiconductors, but they don't seem to have samples of the EXACT model number (NTD60N02RG) when i clicked the "order samples" link for them it put samples for NTD60N02RT4G in the shopping cart. Will these mosfets work, or will they cause more problems?

(PS, any soldering tips i should know?)

This post has been edited by gummyworm31: Jun 3 2007, 08:03 PM
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
RDC
post Jun 3 2007, 08:36 PM
Post #2


X-S Seraphic
************

Group: Head Moderator
Posts: 8708
Joined: 16-December 03
From: VA
Member No.: 82718
Xbox Version: v1.0
360 version: v1 (xenon)
They're the exact same thing in this case.

If you don't have a good soldering iron you'll have a time getting the Drain Tab of the thing hot enough to remove it from the board since it's surface mount.

Have you tested them to see if they're bad? or just whizzin' in the wind and hoping to not catch any spray?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
gummyworm31
post Jun 4 2007, 01:51 PM
Post #3


X-S Young Member
*

Group: Members
Posts: 56
Joined: 21-May 07
Member No.: 343127
Yeah, I've tested those two, but it seems like those two go bad a lot. On my newer motherboard, M$ seems to have switched providors. I wonder if I'll run into the same problem again 2 months down the road. sad.gif
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Joust
post Jun 4 2007, 02:15 PM
Post #4


X-S Member
*

Group: Members
Posts: 132
Joined: 5-December 03
Member No.: 79417
can you post how you tested them?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
pimpmaul69
post Jun 4 2007, 07:10 PM
Post #5


X-S Freak
*****

Group: Members
Posts: 1769
Joined: 31-January 04
From: Colorado, USA
Member No.: 96531
Xbox Version: v1.2
360 version: v1 (xenon)
QUOTE(gummyworm31 @ Jun 3 2007, 08:38 PM) *

(PS, any soldering tips i should know?)

adding more solder will weaken the old solder and make it tons easier to remove
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
gummyworm31
post Jun 4 2007, 09:06 PM
Post #6


X-S Young Member
*

Group: Members
Posts: 56
Joined: 21-May 07
Member No.: 343127
QUOTE(Joust @ Jun 4 2007, 02:51 PM) *

can you post how you tested them?


I tested the resistance between the pin on the bottom, and the top left pin (as Got4M4xx said to do HERE)
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
gummyworm31
post Jun 7 2007, 08:12 AM
Post #7


X-S Young Member
*

Group: Members
Posts: 56
Joined: 21-May 07
Member No.: 343127
I managed to un-solder the 2 smaller pins, but the bottom pin is giving me some trouble. I scraped off the whole top half of the mosfet, but the bottom pin still won't come off. I was frustrated to the point that i soldered a new mosfet on top (only the 2 smaller pins, mind you.) When i push down on the new mosfet, the board gives me a 0001 error. What should I do... blink.gif
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Chancer
post Jun 7 2007, 09:40 AM
Post #8


Don't You Trust me?
***************

Group: Head Moderator
Posts: 18687
Joined: 31-October 03
Member No.: 71217
Xbox Version: v1.6
360 version: v3.0 (falcon)
QUOTE(gummyworm31 @ Jun 4 2007, 09:42 PM) *

I tested the resistance between the pin on the bottom, and the top left pin (as Got4M4xx said to do HERE)

It's not an accurate way to test any Field Effect Transistor
They should also be removed from circuit to test.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
gummyworm31
post Jun 7 2007, 09:21 PM
Post #9


X-S Young Member
*

Group: Members
Posts: 56
Joined: 21-May 07
Member No.: 343127
how hot do I have to get them to actually remove them from the motherboard? my 750* iron dosen't seem to be doing the job...
User is offlineProfile CardPM
Go to the top of the page
+Quote Post




 

Reply to this topicStart new topic

 

Lo-Fi Version Time is now: 24th May 2013 - 09:07 PM
Invision Power Board v2.1.7 © 2013  IPS, Inc.
Licensed to: Scenyx