Xnandhealer 0.7 - Glitch Hack Support, Updated to 0.71 Options

[TingedAce]

** Now updated to 0.71 **

See details and screenshots below.

You can download a copy from here


New in 0.71
-------------
- Fixed the problem of not building XeLL if there was a space in the Working Directory pathname


New in 0.7
------------

- Carry out the glitch hack from start to finish using one application!
- Creation of image_00000000.ecc (XeLL) for Glitch Hack based on original nand dump
- Creation of full Glitch Hack image (using ggBuild) for all model types
- One-click CPU key retreival from XeLL over LAN (and creation of fuses.txt)
- One-click CPU key retreival from fuses.txt file
- Added support for trinity NAND image analysis







Instructions for Glitch Hack (once glitching hardware is installed)
----------------------------

1. Connect NAND programmer and dump the NAND as per NAND dumping instructions
2. Under Build XeLL Reloaded Tab, select a previously dumped NAND image and click "Build XeLL"
3. Click "Write XeLL To NAND" and let it complete
4. Remove NAND programmer, connect ethernet cable to console and boot console from eject button (take
note of assigned IP)
5. Enter assigned IP address in the box (e.g. 192.168.1.9) and click "Get CPU Key from IP". "fuses.txt" will
be created in the working directory.
6. Under "Build Glitch Image" Tab, select a dumped NAND image and click "Build Glicth Image"
(IMPORTANT! For jaspers, make sure that the Model Type is correct)
7. Reconnect NAND programmer and click "Write Glitch Image To NAND" and let it complete.
(No need to remap any bad blocks, ggBuild will have already done it)
8. Remove NAND programmer, and enjoy your glitch-hacked console.

NOTE: Currently, dashlaunch patches will be applied by default. Advanced options will come in a later revision.

This post has been edited by TingedAce: Nov 30 2011, 07:50 PM

[ruciz]

Awesome.

Now I can delete all those batch scripts! Thanks for the amazing program

[TingedAce]

Awesome.

Now I can delete all those batch scripts! Thanks for the amazing program

Cool - I hope it works well for you. It should build the final glitch_image.bin identical to the that from the Multi Builder you're using because it re-uses the same filelist.ini. The only exception is that Multi Builder uses a slightly different filelist.ini for the 4578 Zephyr (if you select it), which XNH currently doesn't.

[effbee05]

Does this not use the Dash Launch patches? I tried for a while to get XexMenu running using the lauch.ini of Dash Launch to no avail. I had to make a new image using 360 Multi-builder with Dash Launch to get XexMenu running to install FreeStyle Dash.

[dave11674]

hi mate

just having a play with this
in settings for the paths...i seem to have some bits wrong
python i dont think i need so i leave that as default
but other paths.. first 1 for nandpro i point to my folder wint nandpro in> ok cos its reading
findsec path> same folder as my nandpro folder > ok
python > ignored
ggbuild > ive pointed this to easy ggbuild by rogero 0.4 and has a couple of sub folders
one being DATA for the 13604 folder and other my360

can you give me any pointers here mate as this is where its failing
do i have to have all the folders in C:\ root
its failing on KV.bin

i have this read in the root of C: by the program along with 3 x 2mb nand images
i have 7 reads from a previous play lol. < full dumps
these dumps have bad blocks mind @ 0FE and 0FF
all 7 images comapre ok so safe there.

so what i did try to do was flash the newly made roger ggbuild image to the machien thru xell with xennon.elf flashed fine
did beef about the bad blocks tho but flashed to 3ff

booted it up ... booted within 5 seconds but crashes just after the xbox logo

so this is where your software comes in
id like to use it to do all my stuff as it seems to be fully loaded with what i need
ie comapre
nand reading
2mb dumps
glitch building
ecc building
its SWEET man i love it

can ya give me some help on setting it up so it will build a full image from my full nand tho

thanks

dave

This post has been edited by dave11674: Dec 4 2011, 01:23 AM

[effbee05]

The python directory should be the same as ggbuild, I assume. I used 360 Multi Builder as the readme recommends.

[TingedAce]

Does this not use the Dash Launch patches? I tried for a while to get XexMenu running using the lauch.ini of Dash Launch to no avail. I had to make a new image using 360 Multi-builder with Dash Launch to get XexMenu running to install FreeStyle Dash.

Yes it uses dashlaunch patches and seems to work for me. Straight after writing the glitch_image.bin I can boot up with a USB stick in the front and I press Guide, Y, A and it runs XeXMenu from USB stick. Here's my launch.ini:

CODE

[QuickLaunchButtons]
BUT_X = Hdd:\Freestyle\default.xex
BUT_B = Hdd:\C0DE9999\00080000\C0DE99990F586558
BUT_A = Usb:\C0DE9999\00080000\C0DE99990F586558
Default = Hdd:\Freestyle\default.xex
[Settings]
nxemini = true
pingpatch = true

hi mate

just having a play with this
in settings for the paths...i seem to have some bits wrong
python i dont think i need so i leave that as default
but other paths.. first 1 for nandpro i point to my folder wint nandpro in> ok cos its reading
findsec path> same folder as my nandpro folder > ok
python > ignored
ggbuild > ive pointed this to easy ggbuild by rogero 0.4 and has a couple of sub folders
one being DATA for the 13604 folder and other my360

can you give me any pointers here mate as this is where its failing
do i have to have all the folders in C:\ root
its failing on KV.bin

i have this read in the root of C: by the program along with 3 x 2mb nand images
i have 7 reads from a previous play lol. < full dumps
these dumps have bad blocks mind @ 0FE and 0FF
all 7 images comapre ok so safe there.

so what i did try to do was flash the newly made roger ggbuild image to the machien thru xell with xennon.elf flashed fine
did beef about the bad blocks tho but flashed to 3ff

booted it up ... booted within 5 seconds but crashes just after the xbox logo

so this is where your software comes in
id like to use it to do all my stuff as it seems to be fully loaded with what i need
ie comapre
nand reading
2mb dumps
glitch building
ecc building
its SWEET man i love it

can ya give me some help on setting it up so it will build a full image from my full nand tho

thanks

dave

Dave, you need to set the ggBuild folder to the Multibuilder\Data folder as that's where ggbuild.exe is.

As long as you're using 0.71 then any folders anywhere should work.

However, one issue right now is you can't use the Multibuilder\Data folder as your working directory. If you've ever set it up like that it'll have removed some stuff you need. In that case just re-extract Multibuilder and try again, making sure your working directory is something else.