Need Help On Glitching A Falcon With Dash 14719 And Cb 5773 Options

[Psyfer9983]

First off, I would have went to Team Xecuter forums to ask this but their site is being a b***h on registration. So their loss.

Second, I have a Falcon. Its been updated to dash version 14719 BEFORE any modding has taken place. The CB is split and the versions of both are 5773. I have a Xecuter Coolrunner version B with Nand-X installed.

Here is the problem. For the life of me, I can not get this thing to glitch. All that the CR does is flash green. It will boot the stock nand with the CR set to program. I have tried everything. I have to use RGH 2.0 and have followed the install guide from J-Runner (heard it was the best). I have tried using a 10 ohm resister, a 15 ohm resister, a 20 ohm resister, a shielded 50 ohm cable, a shorter wire for ALL connections, re-solder the thing at least 20 f*****g times, flashed the hell out of the CR and my nand, tried several different tools to add to the unknown flash count, tried all timing files more times than I care to count, powered cycled more times than I care to count using the eject and power buttons, etc... and still nothing. Its past 4 AM my time and I have be up since 6 AM yesterday, so I'm putting the POS to bed (trying to restrain myself from taking a hammer to it, breaking it into a thousand pieces, gather the pieces up in the grill, light the f***** up, scoop the ashes up in some unmarked container or bag, take a shovel and the container or bag to a remote location, dig an unmarked grave and bury the container or bag making sure to piss on grave afterwards ). If you haven't caught on by now, I'm pissed , sorry. (please disregard red words)

I have modded consoles for years. PSX, PS2, PS3, XB1, 360s (mostly Xeons), ect... and never had this much trouble. This is my first time using the RGH 2.0. I did look online, watched several videos, read several tutorials, saved install pics and guides. I'm not say I know all about this method of modding a 360. I'm just saying I did my homework on it and still need help.

So with that said, any ideas?

[Psyfer9983]

Yep. Tried it all. I used the diagram from J-Runner for the 2.0 install. Using 2.0 diagram, PLL_BYPASS is not used right? It didn't have a wire on it and just want to be sure. Keep in mind, this is an updated Falcon on dash 14719 with CB 5773. I have notice that J-Runner says that there is no separate xell recovery and it also replaces the CB with 5772 not 5773. And whats this about - "XOR HACK NEEDED FOR CB 5773". Here is the J-Runner log window.

START OF CODE

J-Runner v0.2 Beta (271) Started



Version v0.2 Beta (272) is available for download.
Checking Files
Finished Checking Files
Initializing Nand..
Nand Initialization Finished
* unpacking flash image, ....
ECC'ed - will unecc.
UnECC'ed
* found decrypted CD
* found XeLL binary, must be linked to 0x1c000000
* we found the following parts:
SMC: 1.6
CB_A: 5773
CB_B: 5773
CD (image): 5773
CD (decrypted): 9452
* checking required versions...
ok
* patching SMC...
Patching Falcon version 1.6 SMC at offset 0x12A3
* Replacing CD...

* XOR HACK NEEDED FOR CB 5773
* patching CB_B...
patchset for 5772 found, 4 patch(es)
* Applying XOR Hack to CB_B 5773
*** Re-encrypting CB_B with xor keystream
*** Fixing entrypoint
* Replacing CB_A 5773 with 5772
* encrypting CB...
* constructing new image...
* base size: 70000
* No separate recovery Xell available!
* Flash Layout:
0x0..0x1FF (0x200 bytes) Header
0x200..0xFFF (0xE00 bytes) Padding
0x1000..0x3FFF (0x3000 bytes) SMC
0x4000..0x7FFF (0x4000 bytes) Keyvault
0x8000..0x9ABF (0x1AC0 bytes) CB_A 5772
0x9AC0..0x1313F (0x9680 bytes) CB_B 5772
0x13140..0x1913F (0x6000 bytes) CD 9452
0x19140..0xBFFFF (0xA6EC0 bytes) Padding
0xC0000..0xFFFFF (0x40000 bytes) Xell (backup)
0x100000..0x13FFFF (0x40000 bytes) Xell (main)
* Encoding ECC...

100%
------------- Written into output\image_00000000.ecc

END OF CODE

The RED lines is questionable to me.

I just did a rewire (soldering as well) and fried a resister to s**t (poor little guy ). I had to make a pit-stop at Radio Shack for a 33 ohm resister and I'm going to replace him in the morning. As far as the timings, I have used all of them unless there are new ones out there that I'm not aware of. I also found some different shielded wire for the CPU_RST. I cut it about 10 to 12 inches long and grounded the end of it at the CR side. I will up some pics of it if it works.

For now, this project is on hold until I get the 33 ohm resister replaced.

This post has been edited by Psyfer9983: May 2 2012, 08:52 AM