Jasper Cb 6753 + Matrix Glitcher V2 + 14719 Not Booting Xell Options

[SonicDcer]

Hi, i've glitched many slims and a few jaspers with Matrix Glitcher v2, but this Jasper CB 6753 doesn't seem to boot with xell no matter what i do.

The Matrix Glitcher v2 Blue Light turns on for a few seconds, then off, then on for a few seconds, just normal as any other glitch mod i've made before.

I'm running Dash 14719, i've even tried this wiring (below) as well as the one in the diagram in the download section of infinitymod.com and got the same results:



I'm not sure how do i need to put the switches but i've tried these combinations

A)
Switch 1: SLIM

1 ON 2 OFF 3 OFF 4 ON


Switch 1: FAT

1 ON 2 OFF 3 OFF 4 ON

C)
Switch 1: SLIM

1 ON 2 ON 3 ON 4 OFF

None of them worked for me.

Here is my J-Runner Log just to be sure:

J-Runner v0.2 Beta (275) Started



Checking Files
Finished Checking Files
Initializing Nand..
Nand Initialization Finished
Comparing...Takes a while on big nands
Nands are the same
* unpacking flash image, ....
ECC'ed - will unecc.
UnECC'ed
* found decrypted CD
* found XeLL binary, must be linked to 0x1c000000
* we found the following parts:
SMC: 2.3
CB_A: 6753
CB_B: 6753
CD (image): 6753
CD (decrypted): 9452
* checking required versions...
ok
* patching SMC...
Patching Jasper version 2.3 SMC at offset 0x12BA
* Replacing CD...

* XOR HACK NEEDED FOR CB 6753
* patching CB_B...
patchset for 6752 found, 4 patch(es)
* Applying XOR Hack to CB_B 6753
*** Re-encrypting CB_B with xor keystream
*** Fixing entrypoint
* Replacing CB_A 6753 with 6752
* encrypting CB...
* constructing new image...
* base size: 70000
* No separate recovery Xell available!
* Flash Layout:
0x0..0x1FF (0x200 bytes) Header
0x200..0xFFF (0xE00 bytes) Padding
0x1000..0x3FFF (0x3000 bytes) SMC
0x4000..0x7FFF (0x4000 bytes) Keyvault
0x8000..0x9ABF (0x1AC0 bytes) CB_A 6752
0x9AC0..0x1317F (0x96C0 bytes) CB_B 6752
0x13180..0x1917F (0x6000 bytes) CD 9452
0x19180..0xBFFFF (0xA6E80 bytes) Padding
0xC0000..0xFFFFF (0x40000 bytes) Xell (backup)
0x100000..0x13FFFF (0x40000 bytes) Xell (main)
* Encoding ECC...

100%
------------- Written into output\image_00000000.ecc


I've also tried Multibuilder 0.94 with same results.

My soldering is well made (i could take a few pictures if you guys need to see them, just ask).

Maybe i need to reprogram the matrix v2 chip to work with RGH 2.0 ? If yes, how?

It's really weird for me because i have another jasper with RGH 1 wiring and matrix v2 running dash 14719 just fine.

I really don't know what else to do. If anybody could help me i would really appreciate it. Thank you!

[Technitian3]

Maybe i need to reprogram the matrix v2 chip to work with RGH 2.0 ? If yes, how?

You do need to program the matrix with one of the RGH2.0 jed/xsvf files from the TX site: http://team-xecuter.com/xecuter-rgh2-0-official-release/
The D/L link is just above the install pics.

[SonicDcer]

Maybe i need to reprogram the matrix v2 chip to work with RGH 2.0 ? If yes, how?

You do need to program the matrix with one of the RGH2.0 jed/xsvf files from the TX site: http://team-xecuter.com/xecuter-rgh2-0-official-release/
The D/L link is just above the install pics.

Are you talking about Matrix v2 right? because from i've read it is very different and you cannot just program it like matrix v1, it has it's own programming and a set of switches so i'm pretty sure the jed files for the coolrunner will not work with it, besides, there aren't any pin indications of how to connect the programmer to the chip.

[Technitian3]

Sorry bro, I was looking at the chip in your install diagrams, wasn't aware the v2 was such a different beast. If you can't program the v2 it's not gonna be much use for RGH 2.0.