xbox-scene.com - your xbox news information source
Quick Links: Main Forums | Xbox360 Forums | Xbox1 Forums | PS3 Forums
Xbox-Scene Forum Help  Search Xbox-Scene Forums   Xbox-Scene Forum Members   Xbox-Scene Calendar

Giganews Usenet Offers: +1150 days binary retention, 99%+ Completion, and Unlimited Speed/Access!

360 ODD Emulators: X360 Key $99 | Wasabi360 FAT $99 | Wasabi360 Slim $99
C4E's iXtreme Burner MAX Drive: LiteOn iHAS124 DROPPED TO JUST $17


Welcome Guest ( Log In | Register )

 Forum Rules Rules
> How To Flash Corrupted Tsop With 1gen (29wire) Modchip?
MrMajst3r
post Jun 28 2012, 08:18 PM
Post #1


X-S Senior Member
**

Group: Members
Posts: 189
Joined: 31-January 12
Member No.: 461872
Xbox Version: v1.1
360 version: unknown
I got 1.4 Xbox with 1gen modchip installed. I want to flash TSOP and throw this ancient modchip. How to do it? TSOP probably is corrupted (when I desolder point 33 http://www.xbox-scene.com/modchips/ownmod_diagrams.html console is fragging)

When I try to flash, I get "flash error" in Gentoox and "flash not writeable" in Evox.

Modchip has an old Evox bios (without LBA48 support).

I have bridges on top, and on bottom (W points)

This post has been edited by MrMajst3r: Jun 28 2012, 08:52 PM
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
 
 Reply to this topicStart new topic
Replies(1 - 4)
Heimdall
post Jun 28 2012, 09:05 PM
Post #2


X-S Legend
*********

Group: Members
Posts: 5749
Joined: 27-August 08
From: UK
Member No.: 388964
Xbox Version: v1.4
360 version: v4.0 (jasper)
QUOTE(MrMajst3r @ Jun 28 2012, 08:18 PM) *
When I try to flash, I get "flash error" in Gentoox and "flash not writeable" in Evox.

What about the rest of the error message? You know, the important bit, where it gives you some numbers about the flash type, for debugging.......

As to your question, you put a working BIOS on the 29 wire chip, solder it to the Xbox, boot, remove the chip (or at least cut a couple of the wires), then flash.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
MrMajst3r
post Jun 28 2012, 09:16 PM
Post #3


X-S Senior Member
**

Group: Members
Posts: 189
Joined: 31-January 12
Member No.: 461872
Xbox Version: v1.1
360 version: unknown
I'm using Hexen to flashing of course.

I get exactly "flash failed!!!" in Gentoox and "flash not writeable" in Evox.

Console has Winbond TSOP, I know, I have to use Gentoox only.

1gen modchip is already soldered by someone and working. Which wires should I cut? Cut after console boot or after I run flashing app?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
Heimdall
post Jun 28 2012, 09:37 PM
Post #4


X-S Legend
*********

Group: Members
Posts: 5749
Joined: 27-August 08
From: UK
Member No.: 388964
Xbox Version: v1.4
360 version: v4.0 (jasper)
Good to hear you are using HeXEn smile.gif

You aren't flashing the TSOP, you are flashing the chip.

Which error message do you get when using Evox to flash? I suspect that it's "Manufacturer's ID 09 Device ID 00", but it would be useful if you could confirm.

This post has been edited by Heimdall: Jun 28 2012, 09:43 PM
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
MrMajst3r
post Jun 29 2012, 05:49 PM
Post #5


X-S Senior Member
**

Group: Members
Posts: 189
Joined: 31-January 12
Member No.: 461872
Xbox Version: v1.1
360 version: unknown
I've followed by this tutorial, and SUCCESSFULY flashed TSOP with HEXEN.

Thanks, you are really master of Xbox! I suggest you, to write a guidebook about Xbox smile.gif I will order one, with your autograph smile.gif

This post has been edited by MrMajst3r: Jun 29 2012, 05:50 PM
User is offlineProfile CardPM
Go to the top of the page
+Quote Post




 

Reply to this topicStart new topic

 

Lo-Fi Version Time is now: 24th May 2013 - 12:19 AM
Invision Power Board v2.1.7 © 2013  IPS, Inc.
Licensed to: Scenyx