xbox-scene.com - your xbox news information source
Quick Links: Main Forums | Xbox360 Forums | Xbox1 Forums | PS3 Forums
Xbox-Scene Forum Help  Search Xbox-Scene Forums   Xbox-Scene Forum Members   Xbox-Scene Calendar

Giganews Usenet Offers: +1150 days binary retention, 99%+ Completion, and Unlimited Speed/Access!

360 ODD Emulators: X360 Key $99 | Wasabi360 FAT $99 | Wasabi360 Slim $99
C4E's iXtreme Burner MAX Drive: LiteOn iHAS124 DROPPED TO JUST $17


Welcome Guest ( Log In | Register )

 Forum Rules Rules
 
 Reply to this topicStart new topic
> Liteon, drive is unresponsive
bigshow1up
post Oct 1 2012, 06:33 AM
Post #1


X-S Member
*

Group: Members
Posts: 78
Joined: 25-September 07
Member No.: 357159
Ok so I have a liteon drive, the dvd drive would not open, it tried but was stuck. I took drive out of the case cleaned everything. now im getting the green blinking light and the drive will not respond . I hooked up another drive to the motherboard and it worked just fine.


What can I do to fix this, thanks ahead of time.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
wilgo45
post Oct 1 2012, 08:52 AM
Post #2


X-S Expert
***

Group: Members
Posts: 598
Joined: 27-February 10
Member No.: 433658
The green light is blinking because the drive is trying to open. The center light blinks when the drive tray opens. Even when everything is working.

The belt inside, that turns the gears, is slipping. Or stretched out of shape.

Either re-condition the belt or replace.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
iateshaggy
post Oct 1 2012, 11:49 AM
Post #3


X-S Hacker
******

Group: Members
Posts: 2514
Joined: 10-November 08
Member No.: 395127
Xbox Version: v1.6
360 version: v4.0 (jasper)
either that or he's not telling you that he erased the drive.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bigshow1up
post Oct 1 2012, 04:16 PM
Post #4


X-S Member
*

Group: Members
Posts: 78
Joined: 25-September 07
Member No.: 357159
Good point ....the drive is 100% stock nothing has been done to it.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
bigshow1up
post Oct 1 2012, 05:35 PM
Post #5


X-S Member
*

Group: Members
Posts: 78
Joined: 25-September 07
Member No.: 357159
Well I just swapped the pcb into a new working drive and still nothing.....the green light flashes sometimes and stays solid other times.... but the drive is still unresponsive. Im lost as to what is going on
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
BoNg420
post Oct 1 2012, 06:38 PM
Post #6


X-S Messiah
*******

Group: Head Moderator
Posts: 3766
Joined: 4-November 04
From: USA
Member No.: 163327
Xbox Version: none
360 version: v5.0 (360S - trinity)
maybe damage to the connectors or the wires bad or loose in the connector
User is online!Profile CardPM
Go to the top of the page
+Quote Post
bigshow1up
post Oct 1 2012, 07:43 PM
Post #7


X-S Member
*

Group: Members
Posts: 78
Joined: 25-September 07
Member No.: 357159
I replaced all wires with new same problem...I tried the drive out before I swapped the pcb on the motherboard and everything was working fine...I then swapped the pcb and now it will not respond..when i push eject the light blinks but nothing happens when i push it again the light stops blinking but nothing happens in the drive.
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
wilgo45
post Oct 2 2012, 03:11 AM
Post #8


X-S Expert
***

Group: Members
Posts: 598
Joined: 27-February 10
Member No.: 433658
Maybe its the 3.3 v regulator for the dvd drive.

That device is on the main board. Near the port connector for the hard drive.

Or it could be the power reg IC on the logic board of the dvd drive.

You should check the voltages on the power cable. You should have One - 3.3 .... one - 5 v and two 12 volt lines
User is offlineProfile CardPM
Go to the top of the page
+Quote Post
iateshaggy
post Oct 2 2012, 03:14 AM
Post #9


X-S Hacker
******

Group: Members
Posts: 2514
Joined: 10-November 08
Member No.: 395127
Xbox Version: v1.6
360 version: v4.0 (jasper)
so u try one pcb and it works, and the other u get a blinking light and no response. you erased the drive. u got the dvd key first?
User is offlineProfile CardPM
Go to the top of the page
+Quote Post




 

Reply to this topicStart new topic

 

Lo-Fi Version Time is now: 25th May 2013 - 09:25 PM
Invision Power Board v2.1.7 © 2013  IPS, Inc.
Licensed to: Scenyx