ok is there an instillation guide?
or is this adapter not good for these versions
i installed the xchip and adapter as normal but i didnt use the 4 spring wires that are used on the 1.6
when i powered up the chip it lit up red like it should but when i go to install the slayers disc it doesnt read it
i have tried reinstalling the bios (i know the bios is right because i used it before)
tried everywhere even on easybuy forums many others are having the same problem is this adapter only good for the 1.6
any help would be great
i am trying to install on a 1.4/1.5 box

ok i fgured it out the old adapter is apart of the new adapter
all you have to do is seperate the black part and you have the orignal x-chip solderless adaptor
i feel like an idiot because how simple it is but hey i guess no one else could help me.

I too am trying to figure out why easybuy2000 would publicly say again and again that the adaptor is universal (1.0-1.6) yet they don't release any info except for the 1.6 xbox motherboard.

Could you give me some some specifics on what you did to get it to work?
then maybe I can write a small guide with some pics for the next bunch of people who buy the solderless adatpers...

I couldn't even get it to work on a 1.6 with an Xchip that works fine on another 1.6 with the Xodus SP... I RMA'd it after getting no response from their techs and every Xchip forum I've found seems to be a ghost town...just look at the number of posts in this forum group compared to the Xodus one...

The xchip itself is great...I just wish I knew how to solder better so I wouldn't have to rely on a solderless to begin with.

I just wish they still sold those inexpensive 1.0-1.5 adapaters...
(by the way if they still do please tell me where!)

you mean like this?

http://www.modwhiz.com/store/catalog/USA-S...us-p-16151.html

ok 82 z28 i noticed you posted on easybuy2000 forums as well
everyone says the techs are not helping them call them on the phone thats what i did
and as far as adaptor goes the orginal x-chip adaptor is apart of the new adaptor just picture the old adaptor connected to the new one and pull it apart
i emailed you a pic z28
the part of the adaptor that is white comes off
it pulls right off and you have the 1.0-1.5 adaptor the x chip plugs in just like it always did
i hope this is helpful

also i was modding a 1.4-1.5 and it kept fraging found out it wasnt a short or a bad bios it was a bad chip so i am having to exchange for another one

doh!
thanks for the link
I will use it next time around




I think I may have the same situation but I'm not 100% sure yet. still testing, but at least now I'm getting the red LED on the chip (or at least until it frags)

thanks again for the pic

heres some pics for people who are still trying to figure it out


EDIT:
damnit... well XS doesn't like imageshack anymore...
if any one needs the pics e-mail me or pm me

well it took me a while, mainly cause I'm lazy but I finnally put all the pics in one place for anyone that needs them.
The pics can be found HERE

I also have a 1.4-1.5 box, but I am unable to get the xbox to startup correctly after loading the bios

I do not get the xchip logo when I start up the xbox. The xbox begins to frag and i get a service error code 16 with my new 200g hard drive. I put my "loaded" hard drive from my other modded box and this one gives me an error code 5.

Any suggestions, is this just a bad chip?

I also have a 1.4-1.5 box, but I am unable to get the xbox to startup correctly after loading the bios

I do not get the xchip logo when I start up the xbox. The xbox begins to frag and i get a service error code 16 with my new 200g hard drive. I put my "loaded" hard drive from my other modded box and this one gives me an error code 5.

Any suggestions, is this just a bad chip?

well I had my x-chip for about a year. When I started I didn't know too much about static electricity. Kind of stupid at the time. Anyway, I had replaced the adpater with the 1.6 solderless one, I got a little progress but still nothing. Then I replaced the X-Chip and it worked fine.
I might have killed it with static electricity or old age. I haven't heard how long the X-Chip is supposed to last but I'm pretty sure it was my fault.
If all else fails you may have to replace the chip like i did.
Good Luck

does anyone know how to install this solderless adapter on a 1.1 version? the plastic guide is no help! i'm so lost! i purchased the x-chip along with the solderless adapter 1.6 and is says it's compatiable with all x-box versions! yet i can't seem to find any manuals to help with the installation with 1.1!