Ok long story short I found my modded xbox that i had not used in a bout a year or so, it has an xecuter2 with a chip. So i booted it up and from the start i get an error 16..Ive done some serious research and have burned about 8 copies of slayer 2.7.... ( probably the dvd's i have)
How can i install a Dash or get the original one ? I just loaded up flashfxp but how do i figure out my xbox ip address.

The xbox goes as far as the XBOX slash green and xecuter2 pops up at the bottom, I even went as far as loading up an old xbox game and it loaded until i tried to use the shortcut options on the controller to take it back to the dash.

Basically all i need to know is if i can FTP to the xbox can i install my dash again and if not any other suggestions? i figured everything is in working order since i am not getting other error codes.

Thanks in advance

You can't FTP until there is a dash up and running - the FTP server is in the dash.

You have to use DVD-R, burned at 4x or slower. The Xbox won't read anything else reliably. You should try burning HeXEn (Google Heimdall's Xbox Engineering Disc) instead of Slayers - it's newer, and has more tools.

If you are getting Error 16 then you probably need a newer BIOS - one that bypasses the clock loop problem. This also means that there isn't an MS Dash on the hard drive, and you might not be able to boot a DVD. To fix this you need to get an MS Dash onto the drive. There are two possible solutions:

- use a post 2004 (Halo 2 or later) Live-enabled game to install a new dash. Just go through the motions of signing in to live, the first thing the game should do is update (or replace ) the dash.
- if that doesn't work, you might have to take the disk out of the Xbox and use Xplorer360 beta 6 to put a clean MS Dash on your C partition, so you can then set the clock and boot from the DVD. If the disk is locked you'll have to unlock it first with xboxhdm and your eeprom.

Thank you so much for the quick answers. I don't have an old Xbox game to try at the moment but im sure it will be easy to get a hold of one and i am currently downloading Hexen and once i get Nero off it's great "power calibration error" .......I'll try that out
Thank you again

infrarecorder / imgburn
will burn the disk for you without paffing about with nero.

Ok so I got hexen running on the box but now what? I went to install dashboards and I get an error. My C: currently has nothing in it. Should I install the dash in that drive or does it matter what drive it's on? Also if I keep getting these errors could I just now FTP into the Xbox and move the files to whatever drive they need to be on?
Thanks

What are you doing, which errors are you getting, and at which point in the process?

All errors are gone Im just lost .....How do I install a dash. I went to dashboard tools / repair tools and install dashboards and all it shows is it coping from one drive to another.
My current drive show as
C: 0.00mb free
E: 4.870.94mb free
F: 123.408.50
G: 0.00

The moment I take hexen out I get back to the error 13 problem again so I'm assuming no dashboard is being installed. Is it easier just to get hexen running and FTP the files into whatever drive they have to be in?
Does it matter what drive the dash is in? Which other files do I have to switch around ?

Did you read the instructions for "Dashboard Repair Tools"?
As you can see, it isn't designed to install the primary dashboard, and as you didn't build your Xbox with HeXEn it's hardly surprising that it isn't having much effect in repairing the dashboards installed by HeXEn.

You have two choices.
1. Boot with HeXEn then use FTP to manually restore your dash
2. Use HeXEn option "3.5.3. New Disk, NTSC Xbox" or "3.5.4. New Disk, PAL Xbox" to install your dash and set up the rest of your system.

I went with option 2 but I have a couple other questions. Does it matter how I make my partitions. The partitions sizes I posted earlier are from a clean new disk option. From that point how would I go about putting a dash.
Thanks

HeXEn "puts" the dash for you. How you set up F/G is entirely up to your personal preference. You don't have to make any changes if you don't want to - If you're happy with 123GB of storage for games, emulators, media etc. in F then when XBPartitioner 1.1 launches just cancel without writing any changes.

Ok so I did all that and it looked like everything copied over fine. I now have stuff In my C: ,I can even hit my shortcut to go to the dash and I see unleash x but without hexen nothing boots.
I'm currently looking at the unleash dash and it's asking for a bios flash. This is the first time I've been on the actual dash. Also when everything is done should I restart from this cd or just th off normally?

Edit : I am finally looking at a working dash with a clear partition
Thank you so much for the help.

When it's working properly it should start without any boot disk.
UnleashX doesn't flash BIOSes, and doesn't ask you to flash the BIOS. What exactly do you do to get to that screen, what exactly can you see, what exactly is the text on the screen?

Which shortcut? When do you do this? Booting with or without HeXen?


It sounds as though whoever installed your chip flashed a very non-standard BIOS. Almost every BIOS out there has C:\evoxdash.xbe as one of its dash locations, yours obviously hasn't. You have two choices:

- use trial and error to find the non-standard dash name and location that your BIOS is looking for, and put your dash there manually
- use HeXEn to flash a new BIOS that works properly.

Edit: Read your edit, glad you got it sorted.

Might be worth replacing the IDE cable as well. That caused a lot of problems for me after not using mine for a few years. All the errors went away after putting a new one in. My HDD kept reading as 0 and throwing errors as well sounds like what you might have.